Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My task is to implement inbuilt RTC for nordic MCU nrf54l15 series. When i use the below API nrfx_grtc_init, it is throwing a error and returning a error code which is saying...
Hello Nordic Support Team,
I’m working with an nRF5340 using nRF Connect SDK 3.0.2.
I am trying to use the NFC pins (P0.02 and P0.03) as an I2C slave interface. However...
Hi,
I would like to generate a PWM signal specifically on the P0.03 pin of the nRF54L15 using GPIOTE + DPPI + TIMERS.
As far as I’m concerned, Port 0 in nRF54L15 does...
Hello all,
I am trying to run bap_unicast_server example with nrf5340_dk. I used no sysbuild configuration. Then I manually added hci_ipc as it shown at ss
I flashed succesfully...
Hi,
I'm currently working on a project using the nRF5340, and I've successfully configured the I2C0 interface as a static Master in my .overlay file using the following...
Hi all,
I am trying to execute an application in XIP mode from an external QSPI flash on an nRF device (nRF5340, Zephyr + MCUBOOT). The setup is:
Partition file:pm_static...
Hello,
I am using edge impulse library to achieve on-device classification. I now want to put the edge impulse related code to the external flash and use XIP function there...
Dear All, I am facing a rather strange issue with the nrf/samples/wifi/shutdown example. I am working with nRF Connect SDK v3.1.1 and a nRF7002DK board. I am observing the...
I recently upgraded from a Ubuntu raspberry to a Raspery PI5 running PI OS and have two Nordic boards but not able to install the nrfConnect image on the PI image. Is there...
Hello,
We are preparing nrf52832xxAA for certification, Im trying to compile DTM from nRF5_SDK_17.1.0 (same issue on v16.0) Default UART pins run fine without error #define...
Hi, I am trying to migrate my device from s132 7.2.0 to s332 7.0.1, for adding ANT. I have no more access to the SWD. I know it is not tested : docs.nordicsemi.com/.../lib_bootloader_dfu_validation...
I am attempting to integrate the MM8108 with the NRF54L15 SoC as my lead engineer suggested, but now I am finding that it is not that straightforward. We want to make a HaLow...
Dear All, I am developing an application where I need to get the nRF5340 to the low power state, where the chip is consuming less than 10uA when it idle, while using the nRF7002...
I would like to control the RGB LED on the board. I followed the drievr example provided by the nrf sdk, but it doesn't work. As far as I understand, I don't need the signal...
