Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I have a workspace project that currently builds fine, however I am starting some new smaller projects and wish to build them as Freestanding so that I can have them...
Code snippet below produces the error code 0x00000001 during nrfx_spim_xfer:
The same SW in a different project does not produce the error. The error occurs during attempted...
Hello,
I have a project of a device with 2 endpoint plus the GP endpoint (242). It's a coordinator.
at first startup, the green power endpoint doesn't appear in the response...
Dear Nordic,
I'm trying to use the LTE Link Monitor and the Trace Collector V2 at the same time in order to collect trace messages from an nRF9160 DK. However, the RAW and...
Hello all,
I am looking for a freelancer to work on a Matter project based on a nRF52840 SoC.
I am an embedded developer and I did already some experiments with the Nordic...
Pretty new to development, compiled and flashed Zephyr basic samples through nrf Connect for VS Code (board type: nrf52840dk_nrf52840) and suddenly board wouldn't respond...
Hello Team Nordic,
We know that %XSYSTEMMODE command is used to set specific LTE mode. I am also using CONFIG_LTE_NETWORK_USE_FALLBACK.
I have a SIM card which connects...
--
I am using Laird's bl654 dongle. If you download a hex file using nrfConnect for Desktop, the dongle is no longer recognized. It works like open bootloader again only...
Hello,
I have been modifying the examples ble_app_uart and ble_app_c_uart to include direction finding. I perform the connection via scan and advertising and then establish...
I am working through setting up device overlays and am struggling a bit. In some part because I can't find consistency in naming or location or anything. My goal is to set...
Hi,
I have used a Joulescope DC energy analyser to measure the current and power consumption of the nRF52833 DK. I took measurements to see how different TXP powers and...
Hello, I am working on direction finding connectionless locator/beacon (AoA). I ran into a problem in the locator. Everything works fine until "Waiting for periodic sync....
Hello Devzone,
I'm developing a Zigbee gateway using NRF52840 and ESP chip for wifi. NRF52840 it act as an coordinator.
I'm using nrf5_sdk_for_thread_and_zigbee_v4.2.0_af27f76...
Hello All,
I have a problem when I build my project from sample central_uart & peripheral_uart .
I have two nrf5340 called A and B . B scans the broadcast to A to establish...
