Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I've had a lot of success with the nRF51 series but recently came to the conclusion that it isn't suitable for our needs and trying to transition to the nRF52.
I picked...
Hello everyone,
I'm developing my own board using the nRF5340. I am quite lost because of the capacitance matching that I need to perform with the 32M Crystal and the 32k...
Dear all.
I have the nRF52840dk and nrf52833dk kits.
I am having the same problem with this guy. And now my kits lost their Jlink and Com port.
In the answer, I found...
I developed a product on ncs1.9.0. It needs to connect to the nb network and support the gps positioning function. When the device is running, I found a problem that when...
The Zephyr documentation about ADC ( https://docs.zephyrproject.org/latest/hardware/peripherals/adc.html ) mentioned ADC _CHANNEL_CFG_DT usage in device tree and later source...
Hi,
I would like to enable the SAADC to read multiple DPPI channels. I am using a timer to publish multiple channels and my code looks like this:
However, the...
Dear all
I am developing a BLE product, and would like to have a different device name for each unit like Product1, Product2 etc. when advertising, so user can identify...
Hi! We are updating our application from NCS 1.9 to NCS 2.1. In the documentation of the HTTP AT command of the 2.X versions of NCS the XHTTPCRSP notification is documented...
Hi Nordic,
1. I am planning to do DFU update with UART
2. I Build smp_svr and flashed successfully when am using mcumgr its getting NMP Timeout
3. I added CONFIG_MCUMGR_SMP_UART...
Hello,
In my project, I have a device (nrf52833 custom board) which I want to operate in dual role (central/peripheral). I've followed a ble_app_hrs_rscs_relay example...
Dear Sir/Madam,
We developeted a smart device based on nRF52840 chipset(to be more accuracy, we desgined our own module based on this chipset, then our end product use the...
I'm currently trying to change the host name of "https_client" and check the operation, but it doesn't work.
Even after changing the host name back to the original, "Waiting...
Hi,
We want to do provisioning of multiple mesh nodes using pb-adv procedure. we installed nrf MESH app, but we are not able to do provisioning for one node using Pb-adv...
Hello everybody. I'm designing a custom PCB fed by a typical 3.7 V nominal 4.2 V peak lipo battery, where minimal area and thus component count is a key factor. Aside from...
