Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi, I want to enable Bluetooth support on nrf5340 for FOTA. Serial seems to work fine but BT doesn't seem to advertise.
I get the following error after flashing smp_svr...
I have two custom images that I flash to my chip (nRF52832, SDK v16.0.0, SEGGER Embedded Studio). Application 1 is located at 0x26000 Application 2 is located at 0x45000....
I am new to embedded f/w development. I would like to be able to debug zephyr projects. Can anyone recommend a debug probe to use with the nRF5340? and any debugger software...
Are there any other SDK options for nRF5340 than nRF Connect SDK (and Zephyr)?
The chip would be nice, hardware-wise, to a project, but the nRF Connect SDK looks like a...
I am having a similar issue to the person in this post where the wake from deep sleep on an interrupt sometimes works and sometimes doesn't. But for me, it's very consistent...
Hello,
I know this question has been asked a lot. But I haven't found one that matches exactly. I'm trying to flash a custom PCB with an nrf52832. I'm using the on board...
Hi,
I am trying to get a simple LED blinking using a timer, gpiote and the ppi. So the Idea is:
Timer compare event -- PPI --> gpio toggle. I am using the nRF connect...
HI,
I am developing an application which requires BLE connection. I am concerned about the energy consumed by the device during the connection.
I understand that once...
Hello,
I'm just starting to use Asset Tracker V2 from v1.9.1 and it appears that it is missing some device info such as version, carrier and other on the Device Information...
Hello,
I'm trying to send a custom reliable message between two nRF52840 DKs, using the nRF5 SDK for Mesh v5.0.0 and nRF5 SDK 17.1.0, by modifying the light_switch examples...
Up to now I referred to the name of the tag from the west manifest to know the zephyr release. So I assumed that the v2.7.99-ncs1-1 tag was from the zephyr 2.7 branch until...
After executing nrf_libuarte_drv_rx_stop(), nrf_libuarte_drv_rx_start() will produce an error.
In nrf_libuarte_drv_rx_start() t his line in nrf_libuarte_drv.c (Line 625...
Hi ,
i am working on nRF52833dk board. here am running sample example from sdk. i.e. peripheral_lbs example. my query is whatever the Bluetooth api it is calling inside...
