Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
While testing, I encountered the following error after flashing the modem firmware and running the DECT example:
<err> nrf_modem: Modem has crashed, reason 0xfff, PC: 0x0...
Greetings,
I want to change Device name on Advertising. Is that possible? I am using nrfSDk52832, I want when some state of Switch is change, to change advertising name...
I am new to this device, so please bear with me during the inevitable simple misunderstandings! I am scanning for bluetooth devices and getting sensible numbers of devices...
Hi, I have a custom board with an ISP1807 onboard. We'd like to optimize the production process, especially the programming process. We currently use the nrf52840 dk board...
I have a small demo, based on the hello world example, where I have also enabled gpio_keys. I can run this on the nRF52-DK, nRF54-DK but when I come to run it on my custom...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
Hello everyone,
I am using NRF5340-DK for my project and I am trying to combine X509 certificates (using MBEDTLS) with RSA operations (using PSA). This is my current proj...
I am working with the wisblock 4631 from rak, that contains an NRF52840. I am working with the Zephyr infrastructure and uploading code via the Nordic extension for VS Code...
Hello,
We have developed a custom System-on-Module based on the nRF9151 SiP and are ready to begin testing its NTN (Non-Terrestrial Network) capabilities.
Following the...
Thingy91I: Is there a sample project accessing the environmental sensor (BME688) ?
If not, perhaps a project to access a device via I2C by the nrf5340 SIP.
A related question...
I am trying to use the HTTPS_Client example but I am struggling to get it working. It returns 200 unmodified, which makes me think everything is working in terms of the board...
Hi, I’m trying to provision a P‑256 key pair into the KMU at runtime on an nRF54L15 (SDK v2.9.1) but psa_generate_key consistently returns PSA_ERROR_NOT_SUPPORTED, even when...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Hello,
As the LE Audio controller for nRF5340 library is deprecated in favor of the Nordic Semiconductor’s standard Softdevice Controller. We have started to use the Softdevice...
