We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi, I successfully implemented a custom BLE service using this tutorial from Nordic. Also, thanks to a Nordic engineer, I have the QSPI example merged with the ble_app_template...
Hi,
When I open an example project in the Segger Embedded Studios I can first build without a problem. When I change the target
device under Debugger in the project options...
Hi,
I'm struggling to adjust the BLE_blinky example in the Segger Embedded Studio from the NRF52810 to the NRF52811.
I tried to follow the documentation from here (...
Shalom!
In my central nrf52840 board we connect to a TI BLE sensor that has a customer UUID base service and the TI OAD base service both with 128 UUIDs. I succeeded in...
Hi all,
In my project am sending ecg values over ble to android app. During first connection, the values are received and seems to be no problem, but when i disconnect and...
Hello,
I want to increase the number of peers stored in flash. Right now I have FDS_VIRTUAL_PAGES as 3. If I increase this, would I be able what I need? I just need 10 pages...
Hi guys,
I have a problem opening CMSIS Configuration Wizard, but only in Mesh SDK. Because I am working in this SDK, do you maybe know how can I fix this issue. I checked...
Hi, I was testing NCS v1.5.0 and Azure FOTA application and found a bug in the is_update() function
If the current firmware version is shorter than the new one, it may...
Hello, In our current project we are using NRF9160 with NRF52811 as BT device over HCI. Firmware on NRF52811 is just Bluetooth: HCI UART example with pinmux changed to match...
Hi Nordic team, I'm having a custom board and custom application made for that board. Application is based on the zephyr v2.3.0. I decided to move to the NCS because i want...
Hi guys:
a. I use a uart dfu bootloader(loacation: SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart) in 52840 soc...
I'm thinking of replacing the software that was running on "nRF52810 QFN48, S112" with "nRF52810 WLCSP, S112". In WLCSP, the pin assignments of XL1, XL2, nRESET, SWDCLK, SWDIO...
I recently downloaded Keil uVision5 and am trying to run some of the examples that are found in nRF5_SDK_12.3.0 available from on Nordics website on my Nordic51 development...
Hello,
I want to control 2 PWM with different frequencies and hence I am using two separate instances. I want to use only the hardware and not the PWM library. Initializing...
Hi
I am using nRF5_SDK_17.0.2_d674dde with softdevice S140 have sample example as ble_app_cts_c but when i run the code first central disconnected but when i going to pair...
