Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello Nordic Team,
I am working on OTA functionality using nRF Connect SDK 2.9.0 on the nRF52833 controller.
Earlier, my application size was around 320 KB, and I reduced...
Good afternoon,
My device communicates using MQTT a few times a day. After many connections I noticed that communications stopped. Every connection attempt would fail with...
Hello all,
I need to sniff some packets to fix an BLE issue, but I can't find the hex files to program my nRF52840 Dongle. The links provided in the documentation and website...
Hi, I tried to start toolchain manager on my main computer and its not working anymore. I tried to delete all nrf related folders, deleted all apps including nrf connect deskop...
Here is a focused support ticket description for your actual issue:
Device: nRF5340 DK ( nrf5340dk_nrf5340_cpuapp ) SDK Version: nRF Connect SDK v2.5.1 Modem: Quectel...
Hello, I'm working with Power Profiler Kit II and i see that we can use a digital port. I would like to know what the electrical levels for a valid High and Low. I can't find...
Hello, Currently I am working with the nrf connect SDK version 2.8.0 with an nrf5340 SoC. There is no external flash memory. I am trying to build a bootloader with the serial...
I have created a Zephyr Snippet (derived from the cdc-acm-console sample).
I am unable to select it in the Build Configuration. It is listed in the dropbox where the sample...
Hi,
I previously had access to the nRF54L15 Early Access SDK and toolchain, and my local EA workspace has been lost. I need to rebuild my development environment for a project...
Hello,
I am currently implementing a Central device using the nRF52810 as part of a Gateway board.
I intend to connect the antenna via a U.FL connector . My current design...
Is it advisable to POT circuits using the nRF9151? If so, please advise of any precautions. The IOT product that I'm designing requires to be intrinsically safe. As such,...
Hello:
I am developing a board and shields based on nRF5340 (but this question is not really specific to nRF5340, it also applies to most other nRF5x chips). The main-board...
Dear Nordic Experts,
Hello,
i have defined a custom service containing a custom char. value in a peripheral according to https://github.com/NordicPlayground/nRF5x-custom...
Hello,
I am running into an issue when trying to use both GPIO and I2C peripherals on the same set of pins on an nRF54L15 board. I have an I2C bus configured on two pins...
I have two devices on TI CC2538 that having problems talking to the NRF52840 dongle.
The channel is channel 11
There are 8 devices using TI CC2538. Only two of them...
