Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I Just got nRF9151 SMA board, try to test NTN feature , after following instruction to update so called "alpha" firmware, somehow the board can not reflash back to any vesion...
I'm using ncs 3.2.1 with a custom board (Holyiot-20046-v1.0). I used the "Create a new board" function in nRF Connect VSCODE to create the board file. I copied the Zephyr...
hello Nordic
i am working with nrf52832 and nrf52840 using ncs v2.9.2 currently
when trying to build with ncs v3.0.2 i get this error:
File not found: /.../my_app/"sysbuild_swap...
Board : nRF54L15DK
NCS : v3.1.1
When I build an application for the nRF54L15 processor, the "otp" memory region in the auto generated "partitions.yml" file has a size...
Hi there, I have uploaded the BLE sounding reflector code on the xiao nrf54l15 module and after the upload i am getting this on my serial monitor *** Using Zephyr OS v4.2...
Hi,
I am using a custom board based on nrf5340. I have an external QSPI flash that is different from the one defined by default dtsi file of nrf5340. My overlay file throws...
I have a custom board based on nRF5340 with nRF7002 WiFi (duplicated from nrf7002dk board definition). The board builds successfully with west build, but Twister cannot find...
Hello,
I am continuing to work on my project with the nRF54L15 DK and have run into another challenge. Currently, the issue is storing images (320 × 492 bytes) in an external...
In the process of obtaining DNV approval for products equipped with modules including nRF24L01+, I have some questions about wireless communication.
1. Does nRF24L01+ meet...
We are facing an intermittent issue on an nRF52832–based product using bare-metal Nordic nRF5 SDK (non-NCS, non-Zephyr) BLE implementation.
Observed behavior:
BLE initializes...
Hey,
I am plannign on developing a locator tag and I wanted to find some more precise information on when to use AoA and AoD and if it changes the accuracy drastically....
Hi,
I need to save a 16 bit counter into a retained register.
I cannot use the 2 GPRETREG since they are already used and I cannot write internal flash.
I cannot use...
Hi everyone,
I’m facing a linker issue in NCS v3.0.2 while using the Zephyr HTTP client sample with TLS enabled , and I’m looking for guidance on the correct configuration...
