Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Situation
When using vanilla zephyr I get a very verbose generated zephyr.dts file where every line is annotated with the line's origin like the following:
However,...
I am using Wireshark with Nordic BLE Sniffer plugin. The sniffer dongle used is nRF52840. I using it to capture a BLE connection from my laptop BLE to a peripheral BLE device...
Hi
I would like to synchronize multiple devices over wifi.
Over BLE and NRF I see the posts using time slot spi. Is there any way to do this over WIFI?
I found this...
i found [A1A] build code on real device which in hands.
but we can not find [A1A] information on devzone, as of 2026 Apr 25th.
could you let us know more detail of [A1A...
Hello Team,
I am facing strange issue in VS Code. Previously I had installed nRF Connect SDK v3.0.0 and later I did uninstall it.
Today I was trying to install nRF Connect...
I used nRF52840 with nRF5 SDK 17.1.0
Also use freeRTOS from example "ble_app_hrs_freertos"
I need implement System-On mode deepsleep mode. So I use nrf_pwr_mgmt_run...
Hi, based on the nRF5340 Audio DK (nRF5340_AUDIO example: gateway, BIS) we send an LE Audio Stream.
As transceiver we use an Airoha AB156x based speaker: SoC name : ab156x_evb...
For just a first test board off of Thingy 91x design, can nRF5340-CMAA be replaced with nRF5340-CLAA? What's the downside of doing that? Documentation says it's not recommended...
Context : I'm building an embedded application using the nrf52832, that can turn on/off and be configured via NFC. These functionnality are implemented using the t4t library...
Hi,
We are working on a project in which data must be sent to server using NB-Iot.
We are struggling establishing an HTTPS connection with a server using the NRF9160 development...
I'm trying to slim down my application to fit in an nRF52832 (currently overflows RAM when building) so I'm carving things out using the prj.conf file. But I'm running into...
Hi Nordic team,
I hope you’re doing well.
I’m new to embedded development and I’m currently exploring the nRF52 and nRF54 series for a future product line. My idea is...
Hello,
I am unable to use the Segger RTT terminal built into the nRF Connect SDK for VSCode Extension pack with the nRF54L15DK.
I have configured my project with the...
I'm having an issue while trying to install the nRF Connect vsCode extension. I assume that extension has auto board detection feature. However, on my computer, this feature...
Hello,
We have a custom PCB that includes an nRF9160 and nRF7000. We’re planning a hardware update to add external flash memory and would like to know if we can use the...
