Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I am using "nrfutil" v8.1.1 and "device" 2.15.2
If I have my Otii ARC plugged into USB, then "nrfutil device list" crashes nrfutil with it complaining about "serialport...
After moving from nrf9160 to nrf9151 on our prototype, our old firmware resets while trying to set up the LTE connection (this still happens when `CONFIG_RESET_ON_FATAL_ERROR...
Hi,
I am following the below link to enable the FOTA over BLE in our custom project. I have tried the "Peripheral lbs" example and it is working.
https://academy.nordicsemi...
I have programmed an nRF5340 DK with the Auracast Broadcast Audio Source application. I have a pair of Samsung Galaxy Buds3 Pro paired with a Samsung Galaxy Tab S11 running...
Hello,
I am creating my own board with a nRF5340. I see a development board with a PCB antenna. I do not have the thousands of dollars for the simulation software. What...
C:\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560\examples\peripheral\spis\pca10056\blank\ses project is giving me the errors listed bellow when trying to run the example...
Dear Team,
I have nRF54L15-DK and my firmware is running fine over there.
Now I want to use nRF54L15-DK to program & debug standalone NRF54L15 on a my custom board....
Our existing product (already in the market) at Element Science in San Francisco, CA, USA uses an nRF52832 (BMD-350 module by u-blox) and nRF5 SDK 15.3 as base for the firmware...
Hello, I have two nrf52840-dongles which I am using to test ESB. (NCS 3.1.1)
With a few modifications to the ESB prx and ptx samples:
Remove logs except for PTX ESB_EVENT_RX_RECEIVED...
I upgraded my sdk from 2.6.1 to 3.1.1 and after resolving a few issues everything was working just as it was before the upgrade except for MCUmgr. When I run the MCUmgr client...
Hi,
I recently migrated a project from NCS v2.x to NCS v3.x and noticed that the method I previously used to generate a device-unique identifier no longer works the same...
I've seen similar threads but haven't yet found an answer that works for me. I don't know much about encryption but I've been tasked with adding 256-bit AES GCM to our project...
On a BLE Peripheral NRF52840 built with nRF Connect SDK v3.0.2 , high-rate GATT notifications sometimes push the stack into a state where no (HCI 0x13) events arrive for the...
Dear Nordic support:
How long is the single broadcast duration and the broadcast interval for Bluetooth? We would like to know what the duty cycle of Bluetooth operation...
