Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
I recently installed the toolchain on M1 Mac using the automatic installation in the toolchain manager.
However, I noticed that the toolchain manager installs x86 variant...
Developing on ncs 2.1, using vs code and nrf connect extension to debug an application running on nrf 9160dk
I am connecting to aws iot core in a similar fashion as your...
Hello,
I have my BLE Gatt Peripheral application working and running.
I am developing a reader that reads BLE credential.
Application is complete. I flash the .hex file...
Hi
I have configured nrf52840 on my raspberry pi. I want this dongle to stop pairing to other device once connected and also most importantly stop broadcasting once it is...
Hi everyone,
currently I am trying to migrate a project from Segger Studio and SDK v1.8.0 to VS Code in combination with the SDK v2.0.0.
For the Project we are using a...
Hello,
We have observed some issues with downloading firmware update over HTTP over NB-IoT. I'm aware that using TCP over NB-IoT is not recommended, but it is technically...
OS: Windows
NCS Version: v2.0.2 Installed using toolchain manager
IDE: VSCode 1.70.2 + nordic-semiconductor.nrf-connect-extension-pack 2022.5.1
I have applications...
Hi Dev Zone Team,
I have been working with the nRF series for quite sometime and I am having an issue with an nRF52840 based module that I haven't experienced before. I...
Hi,
I'm implementing LESC.
SDK version : 16.0.1
SD version : 7.0.1
example code : ble_app_hrs
I checked that the LESC(just works) function is working.
But...
I'm working on developing a UART Secure DFU platform on the NRF52833 with SDK 17.1 and soft-device s140 v7.2.0.
As there are no direct examples for this application, I followed...
Hi ,
I am new to this nRF5340. In peripherial UART , BLINKY, HELLO WORLD sample program is working fine. i need a support for DF CONNECTIONLESS RX &TX to enable bluetooth...
Hi,
on my Custom Board I'am setting P0.12 to High triggered by a BLE notification (NUS). I'am here using the BLE Uart Example (S112, pca10040). The Custom Board's nrf52832...
