Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
We are looking to use freeRTOS instead of zephyr on this board.
Finally with freeRTOS...
Dear Nordic support team
I tried to change the sample of ble_app_uart (nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040e) to support connecting 4 mobile...
I am working on an e-paper display with Bluefruit nRF52832 . I need to transfer a large image bitmap over Bluetooth Low Energy (BLE).
As BLE can send 255 bits at once, how...
Hi there,
We are using nrf9160 DK v1.0.0 ( pca10090 ). SES version 5.68 nrf Connect SDK 1.9.1 Windows 10
I want to make it as spi slave on pins CS=p0.10, mosi=p0.11, miso...
Hello Team,
We are developing an application with nRF52832 and ncsv1.8.0.
We are using NUS service to share data between Mobile and Nordic Chip. With the help of nRF...
Hey there!
The DFU over serial was successfully implemented. Unfortunately, I was only able to update the first node of my mesh, not all of them.
The first node in the...
Hello!
Recently I want to write a hci vs command in zephyr using nrf connect sdk, when I track ncs_v1.9.1\zephyr\samples\bluetooth\hci_pwr_ctrl samples code and find it...
Hi, for nRF5340 the "Build code" is a string of 3 chars
H - Hardware version code P - Production configuration code F - Firmware version code
https://infocenter.nordicsemi...
Hi
I am testing a thermometer peripheral using the nRF52840DK. It is advertising using BT LE Coded (BT_LE_ADV_OPT_CODED) with an advertising frequency of 3 seconds.
...
Dear Nordic Support Team,
I would like my nRF9160 DK to connect to multiple servers using TLS. Among others, I have read the following documentation: nRF9160: Simple MQTT...
APN setting of nRF9160 cannot be done well.
I am using soracom's SIM, and the contents are as follows.
(When I checked, it was a SIM that supports LTE-M.)
Name: Any (Example...
I'm relatively new to both nRF and Zephyr platforms and I'm wondering how to disable UART on the UART pins (such as p0.19-p0.22 on the nRF5340 that I'm using) so that they...
WHAT IS THE MAXIMUM OUTPUT CURRENT OF DCDC IN NRF52833 OUTPUT IN HIGH VOLTAGE AND NORMAL VOLTAGE MODE?
I AM POWERING UP TWO SENSORS WITH IT THAT USES CURRENT IN MICRO AMPS...
