Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Issue tracking in GitHub seems disabled for https://github.com/nrfconnect/sdk-nrf
Where can i report bugs for the nrf connect sdk v1.9.1?
For instance i just started with...
I´m trying to add Xiao BLE (nRF52840) to the nRF Connect SDK. Here is the configuration part for the flash that I use in the device tree file:
To simplify the configuration...
Hi,
We have an application based on BLE_UART TXing sensor data.
Most of our sensors are read through PPI with minimal code interaction (except for packet counters etc...
Hi, I’m trying to program my nrf52840 dongle. I did have followed the steps from the nrf52840 programming tutorial, but I have some issues.
I’m trying to write the USB CDC...
Hi,
I'm using nRF52810 with SDK 17.02.
When I don't download bootloader my application worked normally. After I downloaded bootloader, there logging NRF_ERROR_SVC_HANDLER_MISSING...
Hi,
I am trying to bring the nrf52 in sleep mode for 12 hours and broadcasting mode for other 12 hours. The idea behind it is to save the battery for longer life. What...
Hi team,
Our customer is working on a sensor related project targeting to use nRF9160-SICA, since their sensor will be placed in some places with high humidity and full...
Hi
I combine the hci_lpuart on the nRF52840 and a program that uses BLE on the nRF9160 on the nRF9160dk. I want to measure the current of this. At the moment I measure on...
I created a simple custom board (in VS Code 'Create a new board' Wizard) based on nrf9160 secure.
I copied the LED part of the original dts and I want to run blinky. ...
Hi Can someone, kindly suggest what are the pop up error notifications in the nRF mesh application for various scanning and provisioning of the BLE-Mesh network, if any document...
I used the Common Application Framework preview sample, with the following additions at end of prj.conf:
NCS 1.9.1 was used
The nrf52840dk then enters deep sleep after...
the cdc_acm speed is faster for my use in nrf5 sdk, but when i use the ncs,the cdc_acm example is use uart line, and the speed is slow, i receive data from rf2.4G radio, then...
I'm working to implement a USB Mass Storage device which uses an external flash memory to store my application's data. I have an nrf52833 DK and a W25Q64FV NOR flash memory...
I/my admin installed the SDK and visual studio though the nRF connect tool chain manager.
When i open visual studio through the toolchain manager it prompts me
to "Select...
Hi All,
I am trying to set up nRF Connect SDK in Visual Studio Code. I am following the guide provided in the DevAcademy https://academy.nordicsemi.com/topic/exercise-1...
