Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello everyone,
I am using NRF5340-DK for my project and I am trying to combine X509 certificates (using MBEDTLS) with RSA operations (using PSA). This is my current proj...
I am working with the wisblock 4631 from rak, that contains an NRF52840. I am working with the Zephyr infrastructure and uploading code via the Nordic extension for VS Code...
Hello,
We have developed a custom System-on-Module based on the nRF9151 SiP and are ready to begin testing its NTN (Non-Terrestrial Network) capabilities.
Following the...
Thingy91I: Is there a sample project accessing the environmental sensor (BME688) ?
If not, perhaps a project to access a device via I2C by the nrf5340 SIP.
A related question...
I am trying to use the HTTPS_Client example but I am struggling to get it working. It returns 200 unmodified, which makes me think everything is working in terms of the board...
Hi, I’m trying to provision a P‑256 key pair into the KMU at runtime on an nRF54L15 (SDK v2.9.1) but psa_generate_key consistently returns PSA_ERROR_NOT_SUPPORTED, even when...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Hello,
As the LE Audio controller for nRF5340 library is deprecated in favor of the Nordic Semiconductor’s standard Softdevice Controller. We have started to use the Softdevice...
I am using the nrf54l15-dk. I had a look at the datasheet and it shows that a watchdog reset does not reset the GRTC. On my code, I tested that and I see that GRTC resets...
Issue: It appears that whether or not TLS is used by an MQTT client MUST be configured at compile-time. An application with the Kconfig symbols enabled to allow TLS to be...
Hi Nordic S .team,
Could you please help me analyze the following inconsistencies, and also provide the requested documentation?
I’m trying to interpret the AuTerm messages...
Hi Nordic Team,
I am working on matter-based product development using nRF54L15 and looking for machine learning support for the same SoC. Can you please confirm if machine...
Hi
I tried to find this file in the SDK folder and it does not exist. I do have it enabled in the stock sdk_config.h
mike@slavebox armgcc % find /Applications/nRF5_SDK_17...
Dear Nordic team,
i am stilll struggeling with the GPIO set-up in system off mode. It seems, that both GPIO_INT_EDGE_TO_ACTIVE and GPIO_INT_LEVEL_ACTIVE are working fine...
