Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I am following below link for DFU over BLE. Link ( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu ) currently it is working fine...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
I'm running into an odd problem with the PWM driver. We're using SDK 17.0.2 and the S113 softdevice on an nRF52833. We're using the PWM module to drive some LEDs.
The nRF52833...
1. nRF Connect SDK v1.9.1
2. Segger 5.68
3. sample name : multiple_adv_sets
I am developing through multiple_adv_sets.
I want to test by changing the uuid in uuid...
Hello
I have installed NRF Connect for Desktop in my system (64bit, i3 CPU). I want to debug my custom hardware using the nRF9160 Development Kit. I have connected the nRF9160...
We have a big application bigger than 500ko and we need a littlefs partition, so we end up with a mcuboot_secondary smaller than the mcuboot_primary (actually we put it to...
Hello, as stated in the Titel im trying to read Firmware Information, for Example the Firmware Version. I tried solving this by reading via Flashareas but no matter where...
Hi,
Datasheet says the sequence as mentioned below,
But the code given in the nordic playground does not follow the sequence mentioned in the datasheet, and the code...
Dear members, with success I implemented the time synchronization example from the nRF5 SDK guide. This example works perfect for a single master, but what if the master changes...
Hi Nordic:
How to use GZLL in nRF52833.
It is only has PCA10040 and PCA10056 In "gzll_ack_payload", but nRF52833 is PCA10100.
I try to use PCA10040 run in nRF52833,...
I start learning open thread in nrf connect SDK using nrf52833, it was pretty fun examples. Now I switch from using cli to send udp from/ to devices to implement it in the...
Hello everyone,
I'm having some issues working with the nRF Connect for VS Code extension in combination with the nrf_desktop application demo from the nRF Connect SDK....
Hello,
VSCode, i change NCS1.9.1 to v1.9.99,
restart computer,but got error:
OUTPUT can not use compilerPath“D:\Program\v1.9.1\toolchain\opt\bin\arm-none-eabi-gcc.exe...
Hello,
I am working with a TOF sensor, and in the init I need to upload some firmware through an I2C connection. It functions as intended when it is a smaller amount of...
