Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi everyone,
I am getting started with the nRF52832 and am testing it with the nRF52DK. I just completed the nRF Connect SDK Fundamentals course and now wanted to test the...
I'm updating our nRF5340 firmware from SDK 2.4.2 to the SDK2.9.0. After few modifications, I was able to compile it using the SDK2.8.0. Now I'm trying to compile it with SDK...
Not too long ago I was able to use Segger Embedded Studio with my nrf52840 DK, compile and build projects and run it. Unfortunately I have moved to a new computer and trying...
Hi Team,
I am trying to commission the matter over thread light app on nrf5340dk with my OTBR using chip-tool but getting below error every time.
OTBR is running on...
I am investigating use-cases around indoor positioning, particularly in commercial and industrial environments (warehouses, factories etc.). The customers prefer to not roll...
Hello,
We were developing on an nRF52840 board with the NCS 2.6.1 SDK and had configured logging and shell capabilities via UART. Once we moved to the 2.8.0 version, we...
We're trying to use the VERSION file, to both generate the app_version.h file (so that the application can know its own version numbers), and to update the version which gets...
Hi there, after installing toolchain and SDK (2.9.0) on Windows 11 (python 3.10) I've successfully build an example and generated the merged.hex but issue occurs when trying...
Hi, one of my nRF52840 dongles cannot be detect in device manager. When I plugged it into a USB port on my pc, the red light slowly blinks and it didn't appeared in ports...
Updating from NCS2.6 to 2.8, the access to my QPSI Flash chip got broken (mx25r64, connected and configured using QPSI exactly as per the nrf5340DK board)
DTS entry:
...
Hello there,
I got an error msg when I tried to compile the Bluetooth LE UART service example for nRF54L15-DK as: " devicetree error: /chosen: undefined node label 'uart0...
Hello, I' needing some help on setting up the MCUBoot for the BL5340PA using the ncs 2.6.2. Currently I have the below add on for the prj.conf for the application core:
...
I am using the LORA Drivers provided by zephyr for testing my SX1762 lora module with NRF52833 Development Kit. I am able to initialize and configure the LORA Peripherals...
Hi,
I am working on an FCC cert of our product which is nRF52811 based. We are currently on SDK 2.0.0. I have copied from the nrf samples bluetooth area the projects peripheral_uart...
1.After I burn AP CODE, executing "nrfjprog -f nrf53 --program factory_data.hex –sectorerase" instruction will cause the following error. This issue wasn't happened in prior...
