Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I have installed the NRF Connect app on my Windows 10 PC, using "Run as Administrator" and keep getting the following error message whenever I try to install any of the products...
This is also my Bluetooth Prj.conf
When I turn on 2.4G, there will be an error message. How can I solve it? BLE and 2.4G cannot coexist at the same time. Can I switch...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
Hello Devzone,
How can the nRF5340 App core read the "version number" of the image flashed to the Network Core, e.g. the FW_INFO fields, or something similar?
I am using...
Hi,
Is there an API, data structure or else in nCS v2.9.0, monitoring of which i can understand if ble advertisement is active or not active or at fault.? Also, if at...
Hi, I am using sdk 2.3.0. I got the following warnings while building the project. The build finished without any error, but it didn't perform as expected. Should I concern...
I am building a project based on the aws_iot example. I am using sdk 2.3.0. I can connect with either lte-m or nb-iot, but I keep getting aws_iot_connect, error: -119. What...
Hello, I am working on a custom board with my own custom project. I want to perform DFU for all the images I mentioned. The mechanism for the OTA update will be as follows...
I am unable to read PDM microphone on my custom board or nrf54l15-dk.
My environment:
- nRF Connect SDK v3.0.2
- nrf54l15-dk
- custom board with Fanstel BM15C -...
Hello,
Revival of an old nrf52840dk board I would like to use for another project, I'm trying to flash a sample application to it but it always fails with the following...
The NDEF message is slightly different between Type 2 and Type 4. Type 4 has a 2 byte length field at the very beginning of the file, called NLEN. The NFC Type 4 example code...
Hi.
I made a board with nRF54L15. I would like to use P0.01 on nRF54L15 as GPIO output., but I failed to confirm P0.01 turn high.
Then, I asked nordic AI anything to solve...
I am trying to use sprintf to format a float type variable, and I am not having any luck. The values printed are either blank or wrong. Sometimes I even Hardfault, which I...
I've got a product on the market that uses an nRF52832 on a custom board. It's been built with NCS V2.6.1
It spends most of its time in System OFF, and gets woken up by...
