Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi Support Team
Sorry, I accidentally pressed the wrong button and closed the following case. I still want to check the following two questions. Many thanks.
(+) Does...
Hi Nordic team,
We are using the nRF54L15 with nRF Connect SDK v3.0.2 for a BLE-based product.
We’ve observed something strange as below:
Advertising range is excellent...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
Background:
Over the past few weeks, I have been working on enabling TLS1.2 for an nRF9160 with Ethernet (W5500). My primary objective is to have both Ethernet and LTE...
Hello everyone,
Currently we're trying to get the full WiFi stack working on nrf7002dk. We decided to look into the power consumption of the DK board itself as a point of...
The Nordic Thingy:91X board has a Nordic nmp1300 pmic device, but the samples do not support the board (a lot of time would be saved it they did);
https://docs.nordicsemi...
Hi Support Team
Does nRF5340 support UAC(USB Audio Class) protocol? We want to input audio to nRF5340 via I2S and PDM and then output the audio to a PC via USB. Can the...
I would like to save about 100KB of data in the on-board FLASH of the nRF9151 SiP. Can you point me to the memory map and how I can partition the space?
I would like to create either a receiver thread that only monitors incoming/MT data OR setup a callback function to receive all incoming messages. Does such a thing exists...
I am using a custom nRF52832 board with NCS v3.1.0 with the following BT configs:
# Enable Bluetooth CONFIG_BT=y CONFIG_BT_PERIPHERAL=y CONFIG_BT_GATT_CLIENT=y CONFIG_BT_DEVICE_NAME_DYNAMIC...
Hello,
im trying to install the credentials into my nrf9160 , the error i get is this one : Failed to obtain CSR from device.
How can i solve this issue? I have also...
I do step-by-step elements from https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-5-fota-over-bluetooth...
I am trying to implemented a mechanism for authenticated debug on NRF52840 on NCS 2.5.
My understanding from the product specification is that DAP protection is enabled...
HI，
The current SDK version I'm using is 3.0.0 for nrf54L15. I want to control the SPIM30 using DPPI, so I'm using the nrfx library to operate the SPIM30. The specific code...
