Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello.
I know that I can change the interval of the advertize event by changing the advertize interval, but I don't know how to set the interval to be sent to each channel...
Hi, We did design our own board/pcb using the nrf9160, but we have a problem to connect to network/lte. I did some debugging and I found out that when the method lte_lc_init_and_connect...
Can you please tell us what is the power consumption in Idle State with DRX = 1.28s and Sleep State with DRX = 1.28s? And an estimate with eDRX at 5.12 s? We are asking because...
Hello, I am using nRF52832 dev kit. I am trying to get lower current consumption. I used ble_app_blinky example and disabled the NRF_LOG. My settings are below:
Role: Advertising...
Hi, I used my NRF52840-DK for few times but suddenly the jlink connection was not detectable. Before the Jlink failed, the main controller on board did not bring up the board...
Hello,
I Cant upload BLE Code on nRF52832 breakout board from nrf52 Dk using Segger studio. Other codes such as blink are uploaded successfully. But there is problem for...
Hi,
I am trying to use radio notifications (mpsl_radio_notification.h) to call notify with data just before central connects. I do this with no problem with NRF52840.
...
Hi everyone. I just bought the nrf52832 Develop Kit. However, after trying to flash write the sample, my nrf52832 Develop Kit doesn't work and won't flash write the next time...
Hi, I'm using BC805M module which uses nRF52805 SoC.
I have a power ON/OFF button on the PCB. If I press the button (deep sleep mode) during BLE connection, the BLE will...
Hi, I'm using nRF52805.
In my code, I used BLE to transmit I2C and ADC data to the mobile app nRF Connect correctly and continuously.
I tried to use NRF_LOG_INFO() and...
Hi. I am working on firmware for nRF9160 based IoT device Already found a way how I can switch between two different images in flash from the current firmware and it's super...
Hi,
I'm trying to achieve a higher transmission speed between nRF9160 and PC on Thingy91 using connectivity_bridge from NCS 1.7.0. On the 115200 everything is working fine...
Hi,
I am trying to flash one nrf52-DK using the other nrf52-DK.I am using nrfconnect App to flash on Linux.
I am getting an error as:
ERROR Could not fetch memory...
