Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Does anyone know what the power consumption of the radio peripheral on the nRF52832 is when it is powered but in the disabled state?
The product specification only offers...
Hi, i'm developing BLE nrf52832.
Is there any way to display the remaining battery capacity on that window 10 when connecting to Bluetooth like that picture?
The remaining...
Hi,
We are programming our devices (nRF52833) in production using a Segger Flasher Portable PLUS.
We use reset after programming via SFR access.
Our devices will not...
I'm using the at cmd library ( commands like at_cmd_write_with_callback ) to communicate with the modem.
I'm trying to enable the nrf_modem library to enable OTA updates;...
Hello
in order to analyze reboot reson (HW \ SW) I use the following:
in case of kernel crash I usually get coldstack print, in this case I can analyze and understand...
Hi guys,
Based on the examples that I found in Zephyr samples documentation, I created the program where I am able to measure the voltage and temperature, and then send...
I tried running pc-ble-driver-py/advertising.py
my command was " python3 advertising.py NRF52 /dev/ttymxc4" and then I got following error
Traceback (most recent call...
Hello
nrf_drv_twi_rx and nrf_drv_twi_tx are non blocking calls?
in the SDK example, I see a while loop is used in the read call for instance which basically is blocking...
I am attempting to build a project with the command line tools as described in: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_programming.html, but it...
Dear all,
Can I achieve ble peripheral whitelist advertising without peer manager? (Assuming central address is already known)
Following are several places that I've...
I have been using the PPK II for about a month.
I just upgraded my nRFConnect to 3.7.1 and when I run the profiler, the PPK II is no longer visible (the big green window...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi, There. I am preparing to program a Mesh application based on nrf52840. The application supports the recovery from the points of power off.
So, I have a question. It...
Hi,
I'm working with the peripheral_uart example in ncs 1.6.1 and wanted to enable flow control for uart0, but do not see a way to do that.
How do I enable flow control...
