Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Dear friends: I am based on the following link: devzone.nordicsemi.com/.../device-firmware-update-dfu-with-mcuboot-bootloader Operation steps test the function of mcuboot...
Hello I am using sdk17.0.2 and nrf52840.
I used nrf52832 to combine ble_app_uart and crypto_aes_ctr codes. And now I'm going to move the code to nrf52840.
However, there...
Hi! I made a custom board with an external flash memory that communicate with nRF52840 through QSPI. I have some boards that works very well, but i have someones that freeze...
I am trying to connect XBee 3.0 Zigbee to a Nordic USB dongle (PAC10059) which has the nRF52840 chipset.
I have been watching the traffic on channel 16 with a CC2531 sniffer...
Hello,
I've gotten the sample AWS FOTA to work on my nrf9160 using a very permissive public S3 bucket, but for production I need FOTAs to use a private S3 bucket.
According...
in fact the error that i posted is related to this file and exactly to the bloc in grey on nvic.h file
" C:/Users/rzaafouri/ncs/v1.5.1/zephyr/include/arch/arm/aarch32/cortex_m...
Excuse me
Prorammmer app in nrf connect for desktop Prompt no device available when I connect thingy91 to PC with mirco-usb cable,I want to update modem， certificate and...
Hi everyone,
We design an application using the nRF52840 and SDK16. This application is intended to be used for gait analysis and one of the requirements is a real-time...
Hello,
I'm trying to initialize the values of all my attributes using sd_ble_gatts_value_set . According to the documentation, the connection handle is ignored if the value...
Hi,
I unsecured my device and running it with JLink RTT to observe logging. If I program uicr registers during this process, the devices gets secured and I have to redo...
Hi,
I'm BLE-sending out Sensor values using a nrf52832. When the sensor gets a (new) value an interrupt is generated and the nrf then transfers the value in the gpiote inerrupt...
Hi. I have read the documentation and I have a couple of questions:
What makes work different mesh_gatt and nrf_ble_gatt? Why can't they work together (maybe it's because...
hi professor,
I add the CONFIG_NO_OPTIMIZATIONS=y but ble connection timeout In my pheripheral project .When I delete CONFIG_NO_OPTIMIZATIONS=y, the ble will connection...
Dear Nordic Team and Community!
I have again a question concerning advertising. Currently I am working with the devices nRF52840Dongle (Advertising, S140, 10059) and nRF52840DK...
Hi, I'm using nRF52805. My "1 button to turn ON/OFF system" code works perfectly fine on nRF52 DK.
However, when I migrate the code to nRF52805, Segger shows me an error...
