Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I am developing application in nRF_connect_SDK v 1.4.2.
I have a problem in Debug the code 1. When i debug the code the breakpoints is not appearing
2. When i...
Hi Nordic,
how do i interpret properly return errors? I l know that it depends on the base address but sometimes it does not correlate at all.
For example, currently...
Dear friends,
We want to update the bootloader in our project. I have read the tutorial about the DFU process from here " Dual-bank and single-bank updates ". I have some...
Hello I would like to change from nrf52810 to nrf52805. I want to take the same code, but I want to change only the gpio because the gpio is different. I was going to set...
When I try to connect to my Pure-FTPd server I always get an error when trying to login, but If I use a public server like... https://dlptest.com/ftp-test/ it's fine. This...
Hey all!
We want to improve the accuracy of the localization of our asset tracking solution, in particular indoors. For that we want to scan Wifi base station advertisments...
Hello,
I am trying to get an MQTT TLS connection to AWS up and running on my thingie91 (nrf9160). I am using SDK 1.5.0 and the sample "aws_iot".
Even though there is a...
Hello,
what is the CPU speed of nRF52832?
I'd like to test if the NRF52832 is running at 32MHz or 64MHz.
I used it to run a compression algorithm, which took 8ms to...
I have seen this question asked a few times--but every thread seems to have no concrete answer.
I have uninstalled and reinstalled all JLINK drivers.
But still get the...
I am using the nRF9160 for IOT with the console connected on UART 0 there is a string of +CSCON: 1 and +CSCON: 0 messages displayed.
Build Zephyr 1.5.1
Modem firmware...
We're looking for some clear documentation for implementing OTA DFU via BLE on the iOS side. We have the firmware working well on our dev kits here, but working only with...
Hi,
Can you explain please why do you use all flash space for application (except SD area) in your examples. For example, SDK 17.0.0, HRS s132 example starts from 0x26000...
Hi
I have nRF SDK 17.0.2, and looking for ble_app_template application for PCA10100 to be flashed into nRF52833 DK. But seems that is not available.
Is there any other...
I'm developing a C implementation for nrfutil to make a Serial DFU in bootloader of sdk11. But I'm having an issue in serial communication. I've used a serial sniffer to compare...
