Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Jonathon LL requested that this be posted as a separate issue: (See Case ID: 336683)
I'm having a problem trying to migrate from 2.7.0 to 2.9.0.
My projects are not...
Using an nrf5340 with nrf7002 wifi, connected via SPI4. Using a shared (chip) antenna, and the COEX signals (pretty much exactly as per the dev board schema).
DTS snippets...
Hello,
I am new to developing on nordic devices.
I currently have a NRF52833DK and wanted to try the USB MSC functionality.
Looking at the latest SDK:
https://docs...
Trying to get started using the nRF Connect SDK for VS Code after using the NRF5 sdk for quite a few years. I have the dev environment fully setup and have been following...
Hi,
I'm trying to develop a Zigbee application, and following the guide provided here for adding a ZCL cluster to the Zigbee template. However, I think this guide is not...
Set up: Rpi Bluez 5.72 (provisioner)
nRF DK (light example)
steps:
1) trigger scan un provisioned devices from Rpi
2) able to see nRF device in scan results
3) start...
Hello,
currently I'm migrating a project from connect SDK 2.6.0 to 2.9.0. After some changes according to the migration guides the project builds fine and also runs.
As...
I would like to use nRF52832 DK to test Nordic UART Service (NUS). But west build failed with the following messages. What is meaning of "zephyr_pre0.elf section `noinit'...
Hello,
I am attempting to use the nRF7002EK shield with my nRF54L15PDK development kit.
I have custom code, but it's based on the wifi scan example provided by Nordic...
Hello,
I would like to know if there is a way that I could see the source code of the nRF Mesh Sniffer app for Android, just like the nRF mesh source code is available in...
Hi, I am currently using the nRF52832 MCU and have implemented hard fault handling as follows: I use the macro APP_ERROR_CHECK(err_code), which, in case of an error, calls...
Hi
I am trying to perform a full modem update on my nrf9160 DK board.
I started at v1.3.4 and successfully used the partial update method to go to 1.3.5
I then used...
