Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi Team,
I just wanted to ask is amazon sidewalk support package for nRF54lm20b is available. If yes, please guide me with steps to add it to the project.
Thanks and...
Hello,
Is it possible to configure an nRF5340 to be both a Broadcast Sink and a Broadcast Source, but with the condition that only frames received by the Broadcast Sink...
Hi,
Any specific reason the errata Anomaly 166 : https://docs.nordicsemi.com/bundle/errata_nRF5340_Rev1/page/ERR/nRF5340/Rev1/latest/err_340.html resolution patch as present...
Hello, I have been testing a simple ble beacon code on my nrf7002dk. And when I connect the ppk2 to the device I see on average of 10 mA. When I plug the ppk2 to a nrf52840dk...
Hi,
while developing a custom driver for the nRF54L15, using the PWM I have found a potential bug.
I have removed the custom driver and just enabled PWM shell and I...
I'm using the PPK2 to develop a product with this device: https://wiki.seeedstudio.com/xiao_nrf52840&_wio_SX1262_kit_for_meshtastic/
Specifically, I am using the Digital...
Hi,
I am developing an application for the nRF54L15 using NCS v3.2.4 , running entirely in the Secure domain .
My goal is to maintain a continuous hardware system time...
The upcoming version of nrf_modem in nrfxlib (labelled v3.3.0-preview1 in the docs; sdk-nrfxlib git commit 6a51711ee4c4c3392a5da4f683e30901820f6b3f) has lost its define `NRF_MODEM_DECT_PHY_SHMEM_CTRL_SIZE...
Good morning Nordic team, we are currently evaluating a migration of our Zigbee firmware from the legacy nRF5 SDK for Thread & Zigbee v4.2.0 to the nRF Connect SDK (Zephyr...
We are experiencing critical data integrity issues on the BLE link of our gateway device. The problem occurs specifically when the device is operating as a BLE-to-Wi-Fi bridge...
Hello Support team,
I have an issue with two simultaneous heaps in my project. I use nrf Connect SDK 3.2.2 with the next configuration options:
CONFIG_REQUIRES_FULL_LIBCPP...
Hello,
I am looking about something similiar which I was able to find for IEEE 802.15.4:
https://docs.nordicsemi.com/bundle/errata_nRF52840_EngB/page/ERR/nRF52840/EngineeringB...
Hi
I'm working on a new project using the nRF9151 SMA DK and I have some questions that I haven't been able to answer by searching this forum or reading through the documentation...
