Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I'm working on a project with nRF51822QFAA on nRF5_SDK_12.3.0.
I'd like to ask if the app_button library uses all four GPIOTE channels?
In my project there are...
Below is the output from a 'bluetoothctl' session for one of my thingy:52's
This is running on a raspberry pi 4 using Ubuntu Mate 20.xx
The output below is using command...
In beacon example code the RSSI value is 0xc3 while converting to decimal it giving 195 and in comment line it is mentioned as dbm.when converting this 195dbm to milliwatts...
hi,
The Fanstel BT832 has a nRF52832. It has TX on P11, RX on P12 for standard uart. I need however rs485 and so need to add a DIR (output) pin. P11 and P12 are not on...
In the mRF24L01+:
Unlike MultiCeiver mode, I have one TRX and multiple PRX units sending back ACK payloads.
In the PRX, what is the purpose of the PPP field in the W_ACK_PAYLOAD...
Hello,
As I understand it, Apple is working on a new product called Airtags. This will be similar to the Tile for finding items like your keys or wallet. The catch is that...
I'm using standard ble_bas from sdk12.3. I set up a timer at 60s interval to use saadc to read battery voltage. Below is my code in saadc event handler for battery level update...
Hi,
I want to add some included services to a new added custom service with nRF Connect, but I can't find a method to do this.
Is there a method to solve this problem...
Hello, regarding to another thread in this forum the debug interface mode can be turned off by sending the command "writeDP 1 0" via J-Link commander or by power cycling the...
Hello,
I'm working with the nRF5 SDK for Mesh v4.2.0.
During the init phase, I call the function mesh_stack_init()
After doing so, the consumption is on average 2.8...
Hello DevZone,
SDK 15.0.0 SD S140
Currently working without an active SoftDevice but even with an active SoftDevice these problems keep occurring.
I'm currently working...
Hello! I need help implementing a TDMA on a nrf52. I've never done this before and Its been hard to find good resources online on the topic so if anyone here has any previous...
I am developing connection between BM833AF Evaluation board and nRF52840, Like a BLE Tag and Beacon. Need support in connection and transmitting data from one to another?...
Hi,
My use case is I have an RGB LED that I want to be green for normal operation, but blink red for 0.5s when a serial driver error occurs.
R, G, and B are each attached...
Hello,
I have multiple questions regarding BL mesh using nRF5 SDK for Mesh v4.2.0
1) is it possible to run this example using 2x NRF52840 dongles(PCA10059) and one NRF52840...
