Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I'm trying to use an iPhone as gateway for nrf Cloud. The user is "Verified" and the "Gateway Name" is the same in the app as the only gateway I have in the nrf Cloud. But...
Hello all,
We check the custom board with nrf52840(BL654) , but it's hang PC and devices when connect the PC.
When the hang on my pc , we checked windows system event...
I'm using SDK 15.0.0 on nRF52832_xxaa.
I'm currently using RTC1 as a low frequency timer to keep track of time elapsed while my device is sleeping. This works well and I...
Hi,
I modified the UART example to work on different pins i.e. pin 17 and 15 on custom board. When I use printf() to print logs, it works. If I use the NRF LOG to print...
Hello,
I am trying to build a small voltage stimulating probe for a research project I am doing. I was going to originally use the Rigado BMD-350 which includes the nRF52832...
Hello,
I am trying to connect my nRF52 DK to my phone (apologies not desktop) and perform a DFU OTA via the nRF Connect app. I'm using SD132 6.1.1, and uploaded the secure...
Hi,
I am using NRF52832 with softdevice s112 and SDK 15.3. I have 20 bytes of data which I want to retain in RAM during system off. I use the following code so that the...
It happens on a new board. It is possible that an HW problem occurs (Xtall), but how to debug it? How to know if Xtall correctly runs? The same code runs correctly on another...
hi ... i am using nRF52832 ,i want to save the battery so i am planning to use system off mode . how to wake up the device from system off mode using threshold value or either...
Hi,
I'm using the "pc-ble-driver-js" to implement a central on PC, trying to send a file through a Write w/o Response characteristic to a device. It's OK for a small file...
Hi ,
I am trying to merging 2 application hex files for example : usbd_pca10056.hex and ble_app_hts_pca10056_s140.hex using mergehex tool.
I could merge the hex files...
I am trying to use segger linker instead of gcc and followed the below link to port the changes
https://wiki.segger.com/Porting_from_GCC_to_SEGGER_Linker
I have tried...
Hello,
i was wondering if it is possible to have a node in a mesh, that is communicating to a PC via a COM-Port. I know it is possible to communicate via the J-Link Debugger...
I want to control network formation process for coordinator and end device through application layer. I refereed light switch example to understand network formation process...
Hi,
Please help, I've been struggling with this problem for a week and I want to get to the bottom of it.
I have production devices in the field based on s110 v7.1.0....
