Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
hi.
I am seeking your assistance regarding a J-Link (PLUS) debugging issue on a custom board featuring the PAN1770 module (ENW89854C1KF), which integrates the Nordic nRF52840...
Need some help with:
nrf5340 - custom board
NO external Flash
DFU over BLE with simultaneous update of both images allowed ( using this devzone concept with static...
Hello Support Team.
I am encountering an issue where the settings_storage partition located in external flash is being erased during an MCUboot image upgrade.
Environment...
Hello, I would like to inquire about some technical details regarding the internal module power supply ranges, power-up sequences, and reset voltages for the nRF54L05, nRF54L15...
Hi,
i want/need to connect & access a microSD Card (32GB) on an breakout board via SPI (technical reasons) and want to use the suggested PINS (28-31) as in the intermediate...
Hi Everyone, I am trying a very simple task of reading PDM Mic with NRF54L Custom Board and streaming the Audio via Bluetooth. I was able to do it very easily with the NRF52840...
Hi： Could you please advise me on how to use P1.01 as the output pin for PWM for NRF54LM20A? I attempted to use the regular IO mode and pulled P1.01 to a high level, but when...
Dear Technical Support Team,
I am currently developing a Matter product using the NCS (nRF Connect SDK) version 3.1.1 . During the build process, the software version string...
Hi Nordic Team,
When using the nRF5340 with XIP enabled, a release build with -Os runs perfectly, but a debug build with -Og crashes on the first function located in the...
Here is a properly structured issue report in professional English.
Project ID
SOFTUART-NRF52-19200-RTT-DEPENDENCY
Subject
Soft UART at 19200 baud works only when...
Issue
When attempting to connect GitHub Copilot to the public MCP endpoint `nordicsemi.mcp.kapa.ai` (as described in the [Kapa.ai MCP integration docs]( docs.kapa.ai/.....
Hello all,
I am investigating the feasibility of building an ultra-lightweight, single-use BLE tracker for short-term insect tracking. Target constraints: - Total weight...
Hi, I am testing the Nordic samples for different environments, and started noticing this strange thing, that sometimes the data output is the same as the previous output...
Hey,
currently I am testing FOTA and it works. The only thing I don't like is the fact that
takes > 10s to appear. Is there a way to make it faster? Because most of...
Hey.
We designed custom PCB board (basically an humidity sensor) with Nordic IC. It works fine, but when I did current measurements I noticed that in advertising mode, uC...
