Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi
There is a github repo https://github.com/nrfconnect/Asset-Tracker-Template/tree/main that receives updates as of yesterday.
However on the documentation website...
I'm trying to get a previously fully functioning MQTT connection back up and running after some hardware difficulties, but am failing to get it to connect to the MQTT broker...
Looking for an example to adapt into my program.
I detect 'smp_svr' but compiling it give me error, it seems I need a flash configuration in file pm_static.yml, but I have...
Dear Nordic Support Team,
We are currently developing a new product utilizing the nRF9160 LTE-M module.
We are in the process of acquiring CE certification for our end...
Hi,
I have been facing issues with the configuration of the nRF9151 for sending and receiving UDP packets via the Skylo NTN network.
I am running firmware version:
...
Hello, on my nrf54l10 I observed a pin (GPIO 1.03) being actively driven low for ~20 ms during a reboot (e.g. Resetting after SystemOff Mode). I need this pin to stay high...
[5/10] Performing build step for 'peripheral_lbs' ninja: error: '/index', needed by 'zephyr/include/generated/ncs_commit.h', missing and no known rule to make it
FAILED...
Since a while back ( github.com/.../999b6a14a4556f16d2f535207a84ceb2cca54f8a) the west flash command with --erase was changed so that --erase would also erase external flash...
Trying to migrate from SDK v2.7.0 to v2.8.0 and suddenly getting the build error
Based on other forum posts, I was able to track down more information using the <build target...
Hi, I just got two nRF52840 dongle and it works great as BLE sniffer.
I want to send continuous BLE data (not only advertising) packet and sniff packets between bonded devices...
Dear Nordic Team,
I am currently working with the nRF5340 DK and would like to know whether it is possible to read or retrieve the Network Core firmware version directly...
Hi,
I am using NCS 3.2.1 and nRF52840-DK's version 3.0.3.
I flashed 2 boards with the openthread/cli sample.
From the CLI on both boards, I issued the following commands...
I’m trying to transmit a payload of up to 2,450 bytes using CoAP over OpenThread. Before jumping into firmware development, I want to evaluate the feasibility of transmitting...
Hello DevZone,
I have some questions about nPM1300. I know that nPM1300 need a battery pack that already contains a PCM.
When the PCM activate the protection due to overdischarge...
Hi,
I'm using the nRF54L15 (custom board, nRF54L15 DK base) with NCS v3.1.0.
I have two UARTs:
uart30 — Shell/console (needs CONFIG_SHELL_BACKEND_SERIAL=y , which...
