Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello, I am using the Soft Device S140 7.3.0 with nRF5 SDK 17.1.0 and the nRF52820 as a peripheral in an NUS application. Initially, the transfer was slow but worked perfectly...
Using the nRF54L15 Development Board.
Did try to run the "nRF connect for desktop" - "Quick start"
I do not get a reply from the Board when doing one of the samples. ...
Hello!
Assume a BLE device already has Bluetooth qualification.
Does FOTA DFU requires new a Bluetooth qualification and additional fees if SoftDevice was updated too...
Hello, I am working on nrf52840 in which the BLE is not Advertising even after i am adding one paramter i just want to add the parameters at the time of adding the 2 parameters...
I am attempting to get the SMP server sample to work on some custom hardware in order to run a BLE FOTA. I'm using NCS version 2.6.1.
I'm able to build the SMP server sample...
Hi team,
I am using ncsv2.8.0, on our custom designed nrf52832 board.
Here I am trying to integrate i2c driver code for bme688 along with bsec library in peripheral_uart...
Hello,
i'm developing a custom board with nRF5340 (WLCSP package) that is very constrained in terms of space for a Bluetooth application. I looked on DevZone and i found...
I first tried nrfjprog which didn't work, but I know that's being retired so that wasn't entirely surprising. After that I moved on to testing 'nrfutil', specifically the...
I am building a BLE audio product that is based on the nRF5340. The application is largely based on the nrf5340_audio ncs example application, but I am modifying the the application...
Hi,
I am testing an actinius_icarus board V2.
I read data from senso BM68X every 500 ms, and publish on mqtt broker every 1 seconds. they are 256 bytes every sending....
Hi,
I am using NRF Cloud + coap comms to send data. However I have encountered payload size limitations that are not configurable via KConfig: sdk-nrf/subsys/net/lib/nrf_cloud...
Unable to find enough information to convert the raw values obtained from Thingy53 for RGB components.
Referred to BH1749NUC datasheet, Thingy53 sample code
Hi,
I am writing a custom i2c driver for an evaluation, when I ran the same i was getting exception:
during troubleshooting i scraped the entire custom driver and...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I'm applying an application firmware update by calling fota_download_start_with_image_type with DFU_TARGET_IMAGE_TYPE_MCUBOOT...
