Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
This is heavily processed code just to show what I'm doing with discovery: I can see that first time I call for discovery I get BT_GATT_DISCOVER_PRIMARY cnt_3 = 3. Then I...
I discovered this chipset and have found a dev board on eBay for $37. Is it worth it to tinker with? I have the 2.8 version of the toolchain. And Sdk. On vs code.
I have...
Why are RADIO_MODE_MODE_Ble_LR125Kbit ， RADIO_MODE_MODE_Ble_LR500Kbit and RADIO_MODE_MODE_Ieee802154_250Kbit not supported in the ESB routines? If I want to use these configurations...
Hi,
I'm working on a project where I want two units to be able to wirelessly send packets to each other whenever they need to. Sometimes only one of the two units may be...
If I initialize the IPC and then turn on the bt_enable, it will lead to the status quo in Figure 2, what is the reason?
If I block k_sem_take (&bound_sem, K_FOREVER) and...
We have a working production system that is based on asset_trackerV2. It is working perfectly but there is a random event happening that I can not explain. On every reset...
Hello, I´m working with the SMP server sample, but I need to modify that one for the following feature related to OTA: 1. Update Nordic firmware with the image system of the...
Greetings,
in Visual Studio code the project workspace looks ok. However NRF Connect is not able to see the application. The error message is of no help:
This did...
Hi everyone!
My name is Natalia, and I’m just starting to work with Nordic. This is my first design, and I’m trying to connect the nRF7002 module to the nRF52840 microcontroller...
I need to match the 50 ohm impedance for antenna performance. It would be easier to manufacture using 4 layers, but I'm planning to manufacture it in 2 layers due to cost...
We are working on product to combine esp32(wifi chipset)+nrf52840(ble, thread and matter ) we wants to keep it as matter device + matter controller to have its seprate network...
We are finishing up our certification process and to complete Wifi Adaptivity, we need to operate the Wifi Shell sample . However, we need to do it on top of our custom board...
Hi,
ncs\v2.8.0\nrf\samples\esb
1. Based on this example, how can customers achieve the frequency modulation function 2. What are some examples for reference? 3. What frequency...
I used this direct test mode sample project: "ncs\v2.6.1\nrf\samples\bluetooth\direct_test_mode"
I can connect and test it normally on the nRF5340 development board with...
