Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Dear all:
I found that the nrf52840 flash size is only 1MB, but the size of light bulb load is about 850KB, I have some questions:
1. Does it contains the FOTA region...
Hi
I am trying to use nrf52811 using nrf52840 DK board.
First, I check simple GPIO example working on my nrf52811 based custom boards
Second, I checked the Bluetooth...
How can I execute a command to commission a device for Thread by using the QR code or pairing code? (without using the pin_code or discriminator) Thanks.
Hi I want to run an epaper with the nRF52832 therefore is SPI needed. Board file was generated from scratch. In the devicetree I added the SPI modul and a epaper modul, which...
Hi,
I am seeing a strange issue with nRF52840 Dongle when I run a custom BLE connection test repeatedly. Below is my configuration:
FW in nRF52840 was programmed using...
Hi,
I'm learing how the i2s streaming works using the example "echo" under "ncs\v2.3.0\zephyr\samples\drivers\i2s\echo". I have a prototype board with nRF5340 and the audio...
When flashing the chip with a build from the samples/bluetooth/hci_uart via west build -b nrf52840dk/nrf52840 samples/bluetooth/hci_uart --pristine and west flash off the...
Hi,
Is it true that you can not disable the nRESET pin in any way? (So that the MCU does not reset after nRESET being pulled low.)
I've gone through the documentation...
Hi Team,
We are using SDK 2.5.2 with MFW 1.3.5
We need to download a secure file from amazon, we first tried to download file from public server connecting to port 80...
Hi DevZone,
My customer found that when using the NRF5340 PDM, there is significant attenuation if the incoming audio signal is a 2kHz signal.
Upon checking the specifications...
Hi DevZone! I am developing a Bluetooth beacon that needs to use extended advertising due to the need of periodic advertising. I am using custom board with nrf52820, nRF Connect...
The following phenomena have been observed in an anechoic chamber:
Success : After the bt_audio_stream_start function is called, the stream_started_cb callback is invoked...
Hello,
We applied for some nrf9151 samples and designed a simple development board with reference to nrf9151 DK. However, there was an issue during testing that the SIM...
Hi, I'm having problems with the firmware update of the Thingy-91. I received it from my professor to use for my final project (it has already been used by previous students...
I am developing a Github CI pipeline to automatically compile, sign, and upload firmware images for a nRF52840 device.
Because I don't have direct control over the machine...
