Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I tested on nrf5_sdk_17.1.0_ddde560，Tested on nrf5_sdk_17.1.0_ddde560\examples\ble_peripheral\ble_app_hrs_freertos project。Call the testfun function to test the test。
The...
Normally when I connected the nPM1300 it would automatically display the battery status and settings,
I already switched up the npm1300 but none ofthem work here.
Is...
Hi
I am working on a project which uses distance measurement config for multiple peripherals with long range.
Our plan is to support DM for up to range 25m and we observed...
I want to achieve time synchronization over a wireless connection with sub-microsecond latency. While PTP (Precision Time Protocol) can provide nanosecond-level accuracy on...
Hi, Nordic Bluetooth Controller Teams, I have a question. I see that the Aux offset of Bluetooth extended broadcast on NCS is fixed at 330us. What is the consideration behind...
Hi,
Is there a Zephyr sample project on QSPI with nRF52840? What I want to do is to write/read to an external flash (W25Q16JVSNIM).
Thank you
Best regards
Dav...
Hello,
I work on a thingy52 since few weeks with a nrf52832 SoC. When i'm turning it on and connecting it to my computer, there is no led turn on and it is not detected...
Im currently working on BLE SMP DFU on Nordic52840DK (Connect SDK v2.7.0) based on this example:
https://github.com/hellesvik-nordic/samples_for_nrf_connect_sdk/tree/main...
Hello everyone,
I am working on a project with a Thingy91 that has an nRF52840 and an nRF9160 , and I am trying to read the battery level. I want to measure this battery...
In ticket Case ID 290251, Torsten Rasmussen provides the following advice to ensure that the toolchain corresponding to the SDK is used to build the SDK (this applies to nrfutil...
I am lab testing Nordic's DECT-NR+ (DECT) for a new factory automation application; I am using the hello_dect sample application from the PHY webinar demo, I am trying to...
I made a custom board, uploaded the Arduino bootloader and was flashing the firmware with Arduino I used it without any problem with revision 2 But when I use revision 3 chip...
Hi! I'm working on the firmware part that needs to perform operations on the same variables both inside GPIO IRQ and the software timer callback. So, there is a need for a...
Hello, I want to send data from peripheral devices to central device. My peripheral device code is based on "ble_peripheral_uart" sample and my central device code is based...
Hi, I'm working on developing a UWP app that can detect any or compatible Nordic devices. let's say a device has BLE capabilities, then through the desktop app i should be...
