Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi, I'm currently working on porting an nrf5340 - NCS 2.6.0 project repo to NCS 2.7.0 starting with my own minimal sample. Having some trouble getting the sample to build...
Hi Support team
Application:
1) We have a Thread network of one leader and 12 child and all of notes run BLE and Thread at the same time.
2) BLE center on the leader...
When I call the function after connecting to the thread network I get a NoBufs error:
My handler:
I'm using an nrf52840-DK and am guessing that it needs more...
In our display project we changed from the SDK 2.6.0 to the SDK 2.7.0.
We driving a SPI display (ST7735r driver)in combination with a touch screen (FT5436 touch driver)...
Hi,
We're using the nrf9160 SoC for our application and we need a way to program both the modem and microprocessor during production. In development we've used a JLink with...
I have an nRF52840 Zephyr based project that compiles/operates fine with SDK 2.5.2 (prj.conf includes the statement: CONFIG_NRFX_GPIOTE=y).
I'm trying to update to ToolChain...
First of all, the f ast mode should be 400kHz, but it seems to be only 200kHz according to the waveform. Also, the duty cycle seems to be wrong.
Secondly, It seems that...
Hello, I have an aht20 sensor from adafruit and an rtc ds3221, the 2 sensors are i2c, except that I am taking this course academy.nordicsemi.com/.../ , but the course in question...
Hello Everyone,
In my project, I am using NRF52832 in my custom board, all function tasks are working fine but when it comes to OTA, the firmware file is transferred to...
hello everyone,
I am designing a device which is operated with coin cell battery, I want to turn on & turn off a device using single button. when device in on mode it should...
Hi,
We are considering a modem delta FOTA on our 9160 devices in field, but find two "approaches" described to this; Either using the modem AT command set ( AT #XFOTA=2...
Hi, Im using a custom NRF52811 board and on this board we are using the internal RC as LFCLK source. I have a single thread that sleeps every 10 seconds, so during 10 seconds...
Hello Nordic,
Currently, we are looking the stack architecture of the BLE provided in the attached link https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/connectivity...
