Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
hello, I am about to get a new computer, I would like to get some opinions about which operating system is the best to use, linux, macOS or windows? right now I am using windows...
Hi everyone,
I am currently trying to flash the MDBT50Q-DB-40 demo board from Raytac but I'm running into some issues with flashing it. I have both referenced the setup...
I want to develop it in visual study code. I have a few problems right now
1. The left nrf icon in the attached image continues to disappear. Whenever it disappears, if...
I can get certain MCUboot features working for the Lesson 8 test program. However, these features don't work when I try to port them over to a fully fledged project. I think...
Hi
This is my first project to make my custom PCB.
I have a question about how can I uploaded my code with segger embedded studio by using nrf52840 dk?
For the hardware...
Hi,
I've create an v2.4.0 SLM application in VS Code by copy from sample, and I am trying to enable trace function for cellular monitor tool app, in order to LOG the packets...
During our evaluation of MQTT, we observed that if we send data every five minutes, the server stops receiving it. We currently believe this is related to CG-NAT, which drops...
Hi I am getting fatal errors when building most of the exercises in the Wifi Fundamental course. I have attached terminal output from building the wififund_less4_exer1_solution...
I have code developed for the nRF52832 based on the Zephyr RTOS. If I switch to the nRF5340 with Zephyr RTOS, would it be possible to develop by simply uploading the additional...
Dear all:
I have built a project(ex: matter bulb) in Nordic SDK, the generated load is zephyr.hex which size is about 2345kb ;
Then I open nRF Connect Programmer, and...
I'm attempting to get our wearable remote to interact with a GoPro using their API and am getting the error in the subject line when attempting to start scanning. I've checked...
I am working on scanning and connecting to an iPhone device in NRF52840dk, but I am not able to receive my iPhone while scanning. If there are any different ways, please let...
Hello!
Looking for some guidance on how I should start debugging an issue I'm experiencing trying to get the Zephyr fdc2x1x sample code running on a custom PCB that uses...
Hi everyone,
I am working with the nRF SDK v2.0.4 for VsCode and with the nRF52840 DK.
I want to develop an application that transfer in real time the data collected...
I'm essentially building a BLE to UART gateway to allow our microcontroller device to talk to our apps. The BLE section is the nRF52840 and I'm trying to simply use it to...
