Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
We have an nRF9160 based product with firmware based on your AWS IoT Core example. Our devices are connected to the Telstra CAT-M1 Network in Australia (50501) using Modem...
Hello,
currently tampering around with "how to find out state of BLE TX FIFO", see e.g.
Next idea: is there any way to access BLE transmission/reception statistics? So...
Hi,
I am hit with a noticeable ram usage bump (~10%) when migrating from 2.5.0 to 2.7.0. Upon generating the ram_report, I notice that net_buf_data_hci_rx_pool has a huge...
The database that nRF Connect for Mobile pulls definitions from is significantly out of date (exact age depends on the category)
https://github.com/NordicSemiconductor/bluetooth...
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
My issue is that even when using...
Hi All,
I am building a event driven IoT application thus using the Nordic CAF I like to know if the Nordic and/or zephyr (system) threads are running fine (if not the watchdog...
Hello,
I am currently migrating from NCS 2.6.0 to NCS 2.7.0 on my board with an NRF9160.
During that process I switched to the new hardware model and to sysbuild. As far...
Hi,
I am getting the following error: CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/extensions.cmake:2891 (message):BOARD is not being defined on the CMake command-line...
Dear Team,
This is my first embedded project.I am basically from Analog design background.
I connected the nRF52840-DK board as shown below.
I connected the board...
Hello and thanks for reading. Our device needs to act as both a central and peripheral. I have written all the peripheral code, and its all working perfectly. However, once...
Hi,
I have a project in which I'm using the nRF52840 with OpenThread and the device is configured as an MTD to minimize power usage. I have recently updated my nRF Connect...
Hi All, I am getting build errors for a project. Project specifics below: - nRF52832 (custom board) - NCS v2.6.0 - Custom board files and other configuration files attached...
My application is running on a nRF9160 using NCS v1.7.0 and modem FW 1.3.0. Sometimes, when our device is in an area with bad LTE coverage, I believe we're overflowing some...
Hi there,
I am using the NRF52840DK development board as a learing experience. I have used the EXCERCISE8 on the Nordic learning program and created a SPI driver for a simple...
Hi all, I am observing some strange behaviour on my two nRF52840 devices. They are running NCS v2.1.0 (Zephyr 3.1.99), one as central and peripheral, one as peripheral only...
