I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
I saw the recent announcements on your LinkedIn, that you're partnering with various NTN providers, that allow one to use LTE over NTN. However, how exactly do I access these...
I have a multithreaded application running on NCS 2.9.0 and I want to be able to see what all the threads are doing at the time of a crash via coredump. I have the following...
Hello team,
We are using nrf52dk with nrf52832 by vs code nrf connect sdk extension.
I have add zephyr led blinky application and flash it on the board and it's working...
Hi,
I like to analyze my custom BLE firmware thread activity, event, and timing using the Segger SystemView application. I have added the following configuration in prj...
Hello,
A super-simple piece of code that enables UARTE1 to receive a byte stream does not seem to work.
It seems as if nrfx_uarte_rx_enable() hangs up.
When I single...
I wanted to check if iOS 18 supports extended advertisements on coded PHY. I am not concerned with the advertisement payload limit but the increase in range that is possible...
I tryed to use the callback function provided by mgmt to hookit, but after including the header file` zephyr/mgmt/mcumgr/grp/img_mgmt/img_mgmt.h `, it prompted that "mcuboot_config...
Hello everyone,
I am currently facing an issue when trying to read data from a block of a Mifare 1K card. After debugging, I found that my program fails to authenticate...
We want to enable 2 way communiaction between Our Nrf9160 devices and server using Websocket secure. We used this as the starting point. We removed anything related to IPv6...
Hello,
We would like to interface an external PSRAM with nRF5340 MCU.
We didn't find any refference on how to do so.
So, my question is it possibel to interface...
Hello,
I'm using nRF9160 and modem firmware version 1.3.6.
I'm using %XRFTEST command to measure RX power received by modem. Command documentation can be found here: https...
I have been through the devacademy lesson on custom boards and am using the nRF53 so have used the custom board for multi-core approach. The example uses the 9151 which has...
I'm trying to add MSC functionality to my project, but I'm encountering the following error:
To understand the cause of the error, I tried creating a new application from...
Hi Nordic Team
We develop a sensor node for a customer based on nRF5340. For now I use a nRF5340DK to do my tests with NCS 2.8.0 (using VS Code).
Based on examples, I...
