HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
We have a separate customized build of MCUBoot for our board. This works fine. Now we would like to remove the MCUBoot build step from our app, but retain the app relocation...
Hello all,
I'm currently evaluating Bluetooth Mesh as potentiell solution for a remote control system with the option to extend the range via range extenders.
To get an...
Hello,
we need to SPI interface of a display controller RM6909 (AMOLED for smart watch) with the NRF52832 processor.
Could you please share us the source code for that...
Hi,
We are currently evaluating the Tracker V2 application.
We would like to increase GPS accuracy, before the nrf9160 returns status GNSS_EVT_DATA_READY. No problem...
hi nordic team，
i have use nrf52840 develop a product ,now i need make sig authentication to sale it .the sdk version i use is 16.0. i m sure it can pass the ble5.0 authentication...
Hey ,
Is there a way to connect and send commands directly using the dongle to the NRF52832?
If so , where can I find a protocol for the communication ?
Hi,
I am testing the sample "machine learning" (from the template nrf/applications/machine_learning) on Thing52. And connect the Thingy52 to the central_uart on nrf52DK_52832...
Hi, in my project I'm using fstorage library to store some information that should be kept even after the firmware update.
For this we are reserving the memory address as...
Hi,
At work we are developing custom HW with an nRF9160, using NCS 1.8.0 for now, but I have confirmed the following behaviour on a nRF9160 DK with NCS 1.9.1 as well.
...
Hi,
after connecting to our mqtt broker I set nrf9160DK to data mode and publish data to our mqtt broker:
After this LTE link monitor is not accepting any AT commands...
Hi,
I am trying to enable extended adverts, when the call to bt_le_ext_adv_create is made, it always returns:
Using the following code:
My custom service has the...
Hello,
I have three devices that use UART, connected to an nRF52832 that I'm using NCS 1.6.0 to program. Since the nRF52832 only has one UART module and Zephyr has no native...
Hi, when following the tutorial, https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial i ran into problems...
hi, I want to use 52832 Comparator function, SDK only has "low power comparator" demo code. Setting reference voltage in MCU, just compare one GPIO with this voltage.
But...
Hi
I was creating a function to send i2c data trough sensor that I use. But when I double check the communication, there is a part that doesn't works properly. So as you...
