Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi everybody,
I'm working on a project where I want to write in an external flash nor memory, and transfer data over BLE. The combination of the peripherical_uart sample...
Hello,
I need to sample 2 saadc channels at 6Khz, and another saadc channel at approx 1/sec for a battery measurement. Which are configured for channels 0,1 and 6 respectively...
Hello all I am using nRF52832 I am using SEGGER Embedded studio for programing. I want to use pins 12 and 11 as Rx and Tx for UART. I changed the default pins to #define RX_PIN_NUMBER...
Hi,
Two weeks ago, I've tested my new devices in an anechoic chamber. I'm using Fanstel BT840X modules. These modules are using nrf52840 for MCU/Radio and SKYWORKS SKY66112...
Dear Nordic Support
I scanned through the DevZone Topics, and found a few tickets concerning MQTT-SN support.
As far as I have seen, MQTT-SN was once supported in the...
How can I enable a matter accessory device to actively send data to a matter control?
I'm using matter-lock sample to test the method of sending data from the matter-accessory...
Hello I have seen ALOT of posts referencing to first build and run ble peripheral uart example and then from there that it will be easy to remove the uart from the functionality...
Task description
I would like to use RTC2's COMPARE_0-event to trigger SAADC's conversion task via PPI, continuously. The RTC needs to operate by itself without CPU intervention...
Hello,
I'm using nRF52840 DK (Central) and nRF52840 Dongle(Peripheral). Dongle flashed with Simulation program which transmits data. DK flashed with hci uart controller...
Hi,
Are there any Thread compatible nRF chipset that are footprint pin compatible wityh nRF52832? I understand/interpret that it is not possible to Firmware upgrade 52832...
Hello,
Our customer has a project that uses nrf52833 as the master and want to connect to the slave of portable ECG meter (ble is Realtek). But they tried for a long time...
Hi,
I am currently working on SoC sensor, which is there is a process for uploading firmware from the controller to a sensor through I2C. So I am creating a function for...
Hi,
We want a solution for BLE Mesh using Coded PHY.
Normally we provision the Mesh devices using Mobile Apps.
We want Nordic module to act as Mesh provisioner to provision...
I am doing NOR flash writing test. It seems nRF52832 enter sleep mode. How can I make sure if nRF52832 enter sleep mode or how can I prevent nRF52832 to enter sleep mode?
