What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Dear Support
Try to modify this use UART_1 for sending out data received via BLE, which is pin P0.14 on nrf52833dk_nrf52833, I modified Kconfig file under the boards folder...
Hello everyone, i am developing a board based on the nRF52832 microcontroller SDK v16.0.0 and sd132 for sending data of a sensor over BLE to a mobile APP. For this i am using...
Hi,
I'm implementing a hard real-time system (few us jitter) on nRF52840, SDK17.1, based on FreeRTOS project.
In the project, I need to sync GPIOs toggling with ADC...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to "WRITE" a characteristic that is larger than the MTU? As an example, we are considering the following...
Dear All,
I am looking for sample code to use an external QSPI flash (MACRONIX MX25R6435FZAIL0). The code is run an nRF52840 based custom board.
Your help is appreciated...
Hi,
I have a doubt regarding the possibility of removing or disabling an endpoint at runtime.
Assuming that we have a device with multiple endpoints, is there a mechanism...
Hi,
I have problem with program nrf21540 UICR mode. POUTA/B_UICR seem not set successful during measured here.
Below following which I write via SPI(Voltage is 3.5V)....
I am trying to use the nRF52840 Dongle as a controller with the Pi and ping devices (e.g. using l2ping to ping my phone)
I have flashed the bluetooth hci_usb sample on to...
Hello,
I am very new at this. I have just started to work with the nrf9160DK board, I am using modem firmware 1.3.1, and nRF Connect SDK 1.8.0. I am trying to test asset_tracker_v2...
Current result:nRF dongle is disconnecting with wireshark and Green led also stopped blinking
1. insert nRf dongle and open wireshark
2. Select nRf dongle(Green LED is...
I'm having an extremely annoying problem. I have an application that uses Nordic NUS service.
(1) I created it from the peripheral UART example for NRF52-DK, and adapted...
Hi.
I'm using PDN example code on zephyr nrf sdk. Please take a look on below log.
Can somebody help me to figure out what are the API can be used to send and receive...
Hi,
Using VisualStudioCode/NRF Connect: Im looking into the sample 'button'. (this because i like to add GPIO-pins to connect to an interrupt)
In the button example...
Hi,
I'm using Manjaro Linux, nRF Connect v3.10.0 and Programmer v2.3.3. I'm trying to connect to nRF52840-DK using this software, but I get an error:
I can connect to...
We are working for "Lighting control model" using BL653 controller ( nrf_653dvk connector) .We are looking for a Test automation framework to test BLE mesh and BLE FUS Based...
