Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I'm using Ubuntu 20.04 with vs code. I'm trying to compile and flash a project using nRF52dk_52832 board. After create new application from samples got the error got error...
To whom it may concern,
Good day, I need your help to activate my sim card on my Nordic Thingy:9. Sim card was provided by Beeline Kazakhstan local provider. Local provider...
Does anyone have a port of nRF5 SDK ble_app_uart_c to the nRF52840-dongle? The goal is to replace the UART with a USB CDC transport.
Thanks in advance.
Cheers,
Je...
hello Nordic
i work with nrf52840, with zephyr (2.6.9)
i have 4 leds on my board that i want to control seperatly with pwm
i put each one of them on a different pwm...
Based on this weblink I need at least 4MBytes of flash for doing a full cellular update on the nRF9160:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples...
There is a custom bootloader in the flash having a address of 0x27000 immediately after the soft device occur, the bootloader code jumps directly to our beacon application...
Hi,
I am using a Mac (Apple silicon) to develop a Matter device. We are using one of the Matter examples, but when importing the example we get the error that GN Tool cannot...
Hi,
When I download my code, I get the error hardfault, but when I reset it, the program runs. I'm not sure why it's giving me this error; could you please tell me how to...
Step Three of "Programming the nRF Sniffer firmware" states:
3. Locate the firmware HEX file for your DK or dongle.
All firmware HEX files are located in Sniffer_Software...
Hi,
I want to know what parameters（<NW-provided_eDRX_value） mean.
The following figure shows parameters
A:Requested_eDRX_value
B:<NW-provided_eDRX_value
C:Paging_time_window...
Hi,
dk: PCA10090 0.9.0 2019.21
ncs: v1.9.0
example: serial_lte_modem
How to send HEX data to the server with the command #XTCPSEND at ncs v1.9.0 the old sdk ncs v1...
Hi,
1. Please provide the COMP input voltage precision in CROSS event on VIN+ and VIN- crossing mode
2. When the input voltage changes to the minimum, the output terminal...
Hi everyone,
i would like to ask if there is available an example project for the nRF9160DK that uses aws_iot through a NBIOT modem configuration.
I took the aws_iot sample...
Hi,
I am trying to connect my LSM9DS1 with nrf52840, this is Arduino nano 33 BLE board. I already figured out that i had to enable it and enable TWI bus. After some readings...
