Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi nordic:
I use nrf9160 to test the new driver mainly due to the following two problems:
Environment: sdk 1.8.0-rc2 modem: nrf9160_1.3.1 lwm2m CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hi There,
I have a question now. If I want to alter the frame format in the data linker, how do I do?
I try to find the source code of the data linker layer in the Mesh...
Dear Members, I want to log my ANT+ HRM into SDcard, I tried with flag, but it never goes to main loop, I'm using nRF52840 Code ANT HRM interrupt :
on the main loop...
hello,
i am using nrf52832 with our customized board and i am trying to send 427 characters string at a time using lbs service but it only accepts 200 characters in single...
Hi! I've got over 2000 smartwatches out in the field that are using the nRF52840. The hardware designers thought it was a great idea to expose the SWD pins along with the...
Hi experienced people
I try to initialize twi on pin 44 and 45.
ret_code_t err_code; const nrf_drv_twi_config_t twi_config_top = { .scl = 45, .sda = 44, .frequency = NRF_DRV_TWI_FREQ_100K...
Is there an easy way to get the manufacturing data from an advertisement packet in the 17.1.0 SDK?
I also struggled with extracting the rssi value and ended up using:
...
I'm using nrfx_saadc V2 in nRF5 SDK 17.0.2. In nrfx_saadc_abort nrf_saadc_task_trigger(NRF_SAADC_TASK_STOP); is called regardless of if the ADC is currently running. If the...
Hi!
We're using the nRF52810 chip, so we have a very limited amount of flash memory. We're looking at every opportunity to save some space. We currently run with a modified...
I've got the USB CDC ACM example up and running. I'd like to do something similar on the nrf52840 Dongle but rather than using a UART for the CLI, I'd like to use a second...
hi support team,
customer has one question about USB device to restart manually, because customer need to change the HID descriptor for some reason.
i tried on usb uninit...
I need your help to design the radio matching network on device nRF52805.
Here the reference design: infocenter.nordicsemi.com/index.jsp In this reference design L1, L2...
Hi Nordic Team,
My dev environment is as follows:
nRF58232+ ses+ sdk17.0+ softdevice 132
We are using BLE Chip on custom board
When we flash precompiled hex file...
Im working with nrf52833dk to implement USB mass storage using the flash to write into txt file.
main.c code is:
when flash and plug the usb the file storage apeare...
