Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
The certification lab is testing nRF52840 RF .They need to test LE coded S=8,Payload Type：11111111：payload length：37
but i can't find Payload Type：11111111 in software nRF_DTM...
I am a beginner I want to advertise for some time then go to sleep mode and wake up do some tasks like advertising and go to sleep mode again. Do all this process recursively...
It looks like the nRF52840 only supports:
8 data bits
1/2 stop bits
even/no parity
So 7E1 is not a supportable mode...is this true? is there a possible work around...
Hi,
I am using nrf52840 and power it by voltage 3v using CR123A battery. As per datasheet minimum operating voltage is 1.7V. But i am facing controller reset at 2.5V. What...
How do we enable a PPI TASK for a GPIO output pin configured using zephyr GPIO driver API? ex: gpio_pin_configure_dt (&ex _pin , GPIO_OUTPUT );
If I just call nrfx_gpiote_out_task_enable...
Hi,
I'm having some trouble getting a device pointer for the OV7670 Camera. I've ported the OV7725 driver. It appears as if the program exits the driver before setting...
So I've been having an issue connecting JLink to programmer v2.2.0.
15:57:24.681
Using @nordicsemiconductor/nrf-device-lib-js version: 0.4.1
15:57:24.682
Using...
I'm trying to upgrade the nRF9160 modem FW on our nRF9160-DK. Programmer v2.2.2 indicates success but the at commands continue to return
at+cgmr
mfw_nrf9160_1.2.3
OK...
I am using the DPPI feature in the nRF5340 to trigger an SPI transaction from a GPIO edge with a delay.
In more detail:
GPIOTE IN event triggers RTC clear task
RTC compare...
Hello,
I've been trying to figure why calling sd_ble_gap_tx_power_set() continues to return the error NRF_ERROR_NO_MEM. I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840...
Hi team,
Currently am working on PWM example from SDK i.e. (Nordic SDK v1.8.0), am testing the pwm example from the sample i'e v (1.8.0\zephyr\samples\basic\blinky_pwm)...
I have nrf52840 pcb without XTAL 32768Hz. When I flash it with Zephyr sample project "Peripheral uart" it doesnt work.
How can I config project to work without XTAL on the...
The application seems to stop at an instance where I invoke a Send call to send data over to a ble central, and the callstack looks as follows. Any way to narrow down the...
I'm using Ant sdh,I want to make system enter sleep,how to disable nrf_sdh_ant?
I usd this function to enable sdh,but can't disable sdh to enter sleep,how to use?
static...
