Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I have an issue when I migrate my app from nrf52 sdk v16 to v17.
I have setup an app with an uart communication, an app timer and a watchdog. All off these (uart and...
We are using the Libuarte - advanced UARTE driver and sometimes see crashes in the uart_evt_handler code in nrf_libuarte_async.c when it gets a NRF_LIBUARTE_DRV_EVT_RX_DATA...
I am interested in developing a Cloud Driver that communicates to my own servers over HTTPS.
Cloud API documentations state that a driver needs to implement a set number...
Can I UART/SPI/I2C on any pin of NRF52832?
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Is there any limit on how...
Hi,
Actually we are searching for a chip which has more than one UART channel for communication.
Can we define more than one UART channel with GPIO configuration? Is it...
Hello, I am currently using the TWI in non-blocking mode, however I frequently run into the issue where the code gets stuck on nrf_drv_twi_tx. function at the return result...
Hello,
i have created custom BLE service/characteristic using this ling https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
So, here i am able to transmitting...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Dear Support
I try to use Watchdog on nRF9160 DK.
I found the sample ..\v1.5.1\zephyr\samples\drivers\watchdog
From there I add to my prj.conf
CONFIG_WATCHDOG=y CONFIG_WDT_LOG_LEVEL_DBG...
Hi,
I wanted nRF5340 capable of reporting the VDD under-voltage event causing a pin reset through a dedicated voltage monitoring IC. For this reason I put a Flip-Flop for...
I am currently experimenting with moving my request for PSM mode into the "lte_lc_init" routine so that it is configured before the modem is moved to Normal mode.
With...
Hi!
I have previously tested connecting the nRF9160-DK to an external MCU to act as an Serial LTE Modem as per the application description. And it worked
fine. Since then...
Hello.
I use nrf9160 and download ota with aws.
After my board download successfull and return event FOTA_DOWNLOAD_EVT_FINISHED, I do system(0) to reboot.
But it can...
Hello,
what is the raw frame to get a good NRF Temperature Service UUID BLE ?
I didn't get custom data (temperature), just the service uuid 0x1809
Here is my raw frame...
