We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. One board is programmed with the proxy client , and the other with the proxy server...
Hello I am in the process of developing a central BLE and I would like to be able to transmit 240 byte frames with a device. The problem I have during my tests is that I see...
Hi,
I get " Could not fetch memory size of target devkit: Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: LOW_VOLTAGE (fffffff4...
I want to use 9 axis motion sensor and I am planning to use INVENSENSE ICM-20948 for this. I know that all the sensors can interface with I2C protocol but the problem is I...
Hello,
DK: nrf52840
SDK: 15.0.0
i want to advertise accelerometer data with BLE/Beacon
so i tried to update the adv. packet for every 10 sec but its not advertising...
BLE DFU Mcu Mgr Error: NOT_SUPPORTED (8)
I am testing the DFU via BLE and get the message "NOT_SUPPORTED (8)" Does anyone have an idea what is not supported?
I logged the following error when I connect my PCA10040 nRF52 development board. The error is: Could not fetch memory size of target devkit: Error: Error occured when get...
Hi there,
First of all; I have experience in Keil but I am new to SEGGER and Zephyr.
Rebuilding our project in Segger using the new nRF Connect SDK I am stuck at adding...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with Paho MQTT-SN gateway on a Raspberry Pi 3 running...
I am using S132 v7.0.1 and while basic Softdevice functionality appears to work fine, I am getting an invalid address error when calling sd_ble_enable(). The pointer that...
I having issues when merging softdevice and application hex files together. If I use nrfConnect and I add the two hex files not merged ( ble_app.hex and s132_nrf52_7.2.0_softdevice...
Hi. I was wandering if there is a difference if I put the TASKS_CALIBRATEOFFSET before TASKS_START , and vise versa. However, I saw in this link: infocenter.nordicsemi.com...
Hi,
According to the documentation the maximum admissible current for the DUT in ampere mode is 1A. What happens if the current goes higher than this ? I suppose that it...
Hi,
I would like to store 180 000 bytes on the flash with fstorage. By using the example after some trouble it works. When I try to apply this example on my own program...
I've seen several questions on this forum on issues with setting up the NRF LOG, however, I am still having many issues and I can't seem to get UART logging working.
I am...
