HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
I'm trying to use the SAADC to return one value so I initialize it, try to take the reading, then unitize it so I can use it for taking readings through the PPI. The SAADC...
By default, is it enabling or disabling bias correction? If no, how to enable bias correction?
Is the RNG peripheral being left on all the time as a result of us using it...
hello,
I need send 10000bytes large data send central to peripheral in single transmission. I using example code ble_app_uart_c in SDK15.2 nrf52832. what are the parameter...
Hello
I am writing low-power application where NRF is called from the other chip by interrupt, performs bluetooth scan and sends data back over UART. Of course, I want to...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
I am using ‘ble_app_bliky” for my application development. In this “Button...
Hello =)
Im trying to run the ble_app_uart_c example on a NRF 52810 Chip.
i got:
SEGGER Embedded Studio for ARM V4.12
SDK 15.3.0
examples\ble_central\ble_app_uart_c...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
In ‘System OFF’ after GPIO interrupt, chip will reset and control will come...
Hi All
I am using nRF52832 with softdevice s132_nrf52.6.1.0
and I have to use both protocol (ble & gzll)
the default protocol is ble
after i keep pressing the button...
Hello,
I am working with nrf51822. I have developed a custom evaluation board. Accidently I connected voltage in reverse polarity to the device now i am unable to program...
Hi,
I am trying to understand possibilities provıded by Bluetooth Mesh Technology.
In my topology, there are tywo types node.
The first type of node is connected to...
Hii,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 2.0.1.
However, when I try to increase...
Hi. I'm using a nRF52840 chip and have a flavour of Proximity profile example being used with some custom services and characteristics that have been added. All is good in...
There is my function for writing to flash.
It works when NRF52832 start from reset, if works when the NRF52832 gets data over BLE but it does not works after "power down...
Hello, for some reason, the UUID's on a Galaxy Note 3 are messed up or are not being read properly. I have included screenshots of the issue. The note 3 is running android...
I'm trying to understand how the UARTs are configured on the nRF9160 DK.
The spec mentions that there are two UARTs, a primary and a secondary. https://infocenter.nordicsemi...
