Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Someone have a example of reading orientation sensor in javascript/HTML of the Thingy:52 equal of the github Nordic Example? github.com/.../Nordic-Thingy52-Thingyjs
Hello, I have a problem with staring "Run" in the "debugger mode" . I used Rigado evaluation board with BMD300 (nrf52) and also work with nrf5 SDK_15.3.0 Examples. Sometimes...
Hello,
I have 2 PCA10056 DK (with nRF52840), my purpose is to check the serialization between App. chip to connectivity chip
I have 2 problems on in each chip:
1. App...
I'm using the code below to enter lp mode;waiting for rtc wake up interrupt to wake up the mcu;
Now I need the app_timer module to do more things ,so I add app_timer lib...
Hi,
I'd like to add a cli command for entering DFU mode .
I'm using nrfConnect on a PC with USB.
When pressing the IF/BOOT button, I can enter DFU and can update the...
Hi,
I am using IAR embedded version 7.40 and my board is nRF52832 PCA10040,while i was checking devices list in IAR IDE under NordicSemi i can see only nRF51 series devices...
hi... i am using nRF52832 , 15.2 version segger . i have merged the uart and timer . i have set the timer for one minute , so every one minute it will send the data to ble...
What is the difference between APIs in below sections:
app_uart_xxx ( under nRF5 SDK v15.3.0 > API Reference > SDK common libraries )
nrfx_uart_xxx ( under nRF5 SDK v15...
Hey guys,
i would like to test my little nRF52811 board, is there any example i can start with? I know there is no software support for direction finding and so on right...
i'm trying to build a scanner that scan only a list of devices , and i want to use a whitelist .
i didn't understand the concept of the new whitelisting in SDK 15.2.0, i...
Hi,
This is a situation after registration. See the following link for detailed information of the setup:
https://devzone.nordicsemi.com/f/nordic-q-a/45544/nrf9160-dk...
Hi
We update our mesh nodes using nrfutil:
nrfutil --verbose dfu serial -pkg client.zip -p COM%Comport% -b 115200 -i 700 -fc --mesh
The package including python is quite...
Hello,
I previously asked this question on the Zephyr forums, but as quite a few days have passed and still not sure what my options are, am hoping I can get some help here...
Hi Nordic, I have a nRF9160 Development Kit. I am a Beginner and lives in Germany. So, therefore I already have a sim from 1NCE. To start from basics, I programmed the DK...
