I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I'm trying to debug a high current issue on a custom board based on the nRF52832. I'm currently loading a modified blinky app (entire main.c included below). On the nRF52DK...
hello,
I am using nrf52 DK and MPU 9255 .I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in...
Hi all,
I have a Thingy52 and a nRF52-DK.
I have successfully setup 2 different Eclipse projects to compile code for both hardware.
On the nRF52-DK, i was able to build...
I am developing Firmware for NRF51822, S110 in Eclipse. I Heard that there is two mode in Firmware. 1. Debug mode 2. Production(release) mode. Is there anything like that...
Hi,
Currently I am browsing the mesh sdk to get enough information for my own implementation,
However sometimes its quite difficult to see what a C/H file actually does...
Hi,
I am trying to use nRF52832 dev kit(pca10040) as my connectivity board and STM32L4 as my application board. I have flashed ser_s132_uart(examples\connectivity\ble_connectivity...
Hi,
I have seen alot about the declaration process with the Bluetooth SIG but couldnt find my specific case.
We made a BLE application with the NRF51, a PCB Antenna, SD130...
I haven't found specific documentation on this so I would like to be absolutely certain that the fields in the softdevice info structure are used how I think they're used...
Reffering to the boilerplate: NordicSemiconductor/pc-nrfconnect-boilerplate
Can someone make a quick guide to create a reducer that is connected to the nRFConnectCore[0...
Hi,
I am running Keil uVision V5.23.0.0, debugging a 51822 using the J-LINK / J-TRACE interface built into the chips
My code uses SD110, SDK 7.2
I need to get ABSOLUTE...
Hi,
The datasheet for the nRF52840 says that the SWDIO and SWDCLK lines have internal pullup and pulldown resistors already, and thus, does not need external ones.
Two...
I am having trouble tracking down some lingering interrupt source that is waking my application up from the power_manage() command. I am turning off bluetooth advertising...
Hi,
I cannot find the pinout for the P9 connector in the Thingy (programming). My idea was to use the NRF52 DK to program it as this video suggests:
www.youtube.com...
