Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello there,
I am developing a coap based client-server application which has thread mesh network. Client is a sleepy node here.
Dev kit: nrf52840
Thread SDK: nRF5_SDK_for_Thread_v0...
Hello everybody,
I want to see integer number with use NRF_LOG_INFO . I try to this;
But RTT_Viewer show like this;
"You have 536881776 trial rights."
I have to...
I am using Nordic NRF528321 with SDK 11.0 and soft device S132 as ble central.At peripheral side it is Nordic NRF51422 with SDK12.2 and soft device S130.I am trying to pair...
Hi,
I'm on nrf52dk platform.
I have flashed the MQTT publisher firmware in IOT section provided in nRF5 SDK 14.2, config the ip address and auth info in code; established...
Hello, I am using nrf52840 PDK, sdk 13.0.0. I managed to read accel, gyro data from the MPU9250 using MPU library based on this example . However, I got magnetometer reading...
Hi guys,
I start with SDK13 and i want to create SDcard saver same information every 5 second on card. This is my code, i have no idea why it din't work.
I red that...
Hi,
i am trying to compile nrf51_sdk example using linux
I have 1- gcc-arm-none-eabi-4.9-2015q3 in location /usr/local/gcc/gcc-arm-none-eabi-4.9-2015q3
also install...
Hi there,
How in the question title, what could be more efficient? use a nrf_delay_us or Timer with HFCLK source.
I am creating a custom protocol to transfer data between...
Hi, is it now possible to flash (via DFU OTA) a nRF51X without the nRF Dongle, but with a generic BLE dongle on Windows 10 ? Thank you for your answers.
Hello,
I am using Nordic's iOS library to perform DFU in our app to upgrade firmware on some BLE devices. Before the DFU, the app scans it as "Paradevice", but reads it as...
Hi,
I'm designing a prototype board with the nRF52832-CIAA and was planning on using the Johanson 2450FM07A0035T integrated 2.4 GHz filter, but have not been able to find...
Hi
in pcb designing of the nrf52832 we use two oscillators one is 32 MHz and another one is 32 kHz.
can't we use both 32 kHz instead of one 32 MHz for saving power consumption...
Hi,
I can't seem to find an example for receiving an update about restored value of CCCD when a bonded peer reconnects. I'm using SDK14.
NUS and HRS examples which use...
