I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
On the nRF52840 using ncs/zephyr v2.6.1, how can I explicitly configure the Coded PHY scheme (selecting either S=2 or S=8) for BLE Extended Advertising? Please provide the...
I tried to fully replicate the example from DevAcademy ( academy.nordicsemi.com/.../) for my project, and added a button and an LED in the overlay. However, once SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello,
We need to interface the nRF54L15 with a 3-wires SPI slave (which uses one single bidirectional pin for MOSI and MISO).
I see two options here:
1. Connect the...
Issue
On the nrf54lm20 using DTLS with MbedTLS, MbedTLS's heap can be exhausted. This will result in a TLS handshake error. When this issue happens MbedTLS does not catch...
Hey,
I have a question regarding the watchdog in a low power application with dynamic sleep times of e.g. 1mim/10mim/1h. In the docs of nrf9160 and also nrf9151 it says...
Hey Nordic support, We want to perform EMC tests on the DECT NR+ for our product and need a continuous wave or tx tone sample for testing. I found the DECT NR+ shell sample...
I mean like when ever i click pristine build in the vs code i am getting this below error " Unable to build: SDK not found. Ensure that a valid SDK is used for the build configuration...
Hi,
We are using the NRF9151 with AT commands to replace our SIMCOM modems.
We would like to write the SIM profile data to the modem via AT commands just like SIMCOM...
Trying to config TDM SCK for: Master, 4 channels, 24 or 32 bits, 16 KHz...doing the math yields 1.536 or 2.048 MHz for SCK. I have 24 MHz or 32 MHz available as possible clock...
Hello, I have a question regarding external flash erase via `nrfutil` command line tool. Does the `nrfutil device` command support doing a qspi erase with custom qspi commands...
Hello,
There is a minor issue identifying a sysbuild configuration if the initial generate and build fails.
Steps to repro:
- add a kconfig that doesn't exist in...
In the past, I've been told I can bypass a lot of the Zephyr nonsense and use the HAL layers of the nRF Connect SDK directly. So if I want to use what was called nrfx_twim_xfer...
