Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
The documentation here:
https://docs.zephyrproject.org/apidoc/latest/group__bt__gap.html#gae11eb8ad254418c38a0e8689df25a159
says, I can call l bt_id_create() before bt_enable...
Hi Nordic,
I am working on code which utilizes the DM library on many devices in a room. Can you please help with a few questions?
Some devices are always initiators...
Hello,
Im currently Implementing Last will and Testament message on my device, Im not using the AWS Libraries here.
Any suggestions on how to Implement this feature...
Hi, from nRF52820 datasheet, some GPIOs pins are stated it use for low frequency I/O only with up to 10KHz.
May I know is that mean these Pins are not suitable for SPI?...
Hello, I am new to BLE and I need help with Battery Service notifications. I am using nrf52840dk, nrf sdk 17.1.0 and I am using ble_app_proximity example which already uses...
Hi all, I have used the nRF mesh app to provision three nodes into a mesh and verified the functionality using the mesh app. I used the export function to dump the mesh configuration...
Hi,
my project is based on the example 'ble_app_proximity' from SDK ver 17.0.2. When I set a longer DEVICE_NAME, for example
the string is cut up after the first 12...
Hello everyone,
I am developing a wearable device using the nrf52832 chip, sdk11.0.0 and s132_nrf52_2.0.0_softdevice.
Because of battery capacity limitation, I have to...
In UART async mode ( CONFIG_UART_ASYNC_API =y) the UART transmit data and receive callback works fine. I've been able to set up the callback and enable the rx.
After switching...
I'm currently setting up an environment in Visual Studio Code because the roadmap suggests going there.
I have experience with Segger and Nordic Segger and with Zephyr....
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi, I am coding an application on nrf connect sdk 1.9.1. which requires to send some data at 25packets per second. and each packet will be ~37 bytes. On the receiver side...
Summary: My custom board with an external crystal is consuming 208 µA when powered down under Zephyr, and I need to reduce it to less than 20 or so.
My board is based on...
Hi,
I'm working on a project trying to build a simple application on my own customize board with nrf52833 SoC.
After the configuration to my own board(Leds, button GPIO...
